English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 22 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author First Project, spool jam and other issues Answered Par Robin on Feb 21, 23 2147 16 Ryan Print Creates Lip at Top Edge Par dhavener on Feb 18, 23 2411 1 dhavener Perimeter misalignment - Terrible surface fini... Par Serch-Aerobuil... on Feb 18, 23 1510 1 Serch-Aerobui... Odd XYZ Calibration Issue Answered Par Alex Wait on Feb 18, 23 1897 3 Alex Wait XYZ calibration failure Par Nimitz on Feb 17, 23 2045 3 Nimitz Another first layer problem. Par budgie on Feb 16, 23 1930 3 budgie Printing a replacement part, and minor 1st pri... Par RandyM9 on Feb 15, 23 2281 8 Culprit First layer - very unsatisfactory results Answered Par karl-herbert on Feb 14, 23 1912 4 skaddisbladis Test print looks a bit odd Par Diem on Feb 14, 23 2381 7 elan Fresh setup – continuous beeping Par Diem on Feb 13, 23 2655 4 Wolf Stringing worse than my ender 3 with same sett... Par danifrancescon on Feb 12, 23 3213 7 danifrancesco... First layer not constant in time Par gagou7 on Feb 12, 23 2018 5 gagou7 Newbie question regarding z-axis calibration Answered Par James McCullou... on Feb 11, 23 2123 10 James McCullo... clogged nozzle on mk3s+ Par Robin on Feb 10, 23 2146 2 RMIL loud x axis motor Par Hello on Feb 09, 23 2080 2 Dawnbringer6 Warping and temporary layer shift Answered Par Mihai Dincules... on Feb 07, 23 2148 4 Mihai Dincule... Trouble with Z calibration? Par Matt Sheets on Feb 05, 23 1514 3 Matt Sheets Z wobbling and shifted layer on overhangs Par Thomas Cheng on Feb 04, 23 2652 12 Thomas Cheng hotted temp not settling even after a PID Par Hello on Feb 03, 23 1539 2 willeykj Missin top layer? Par karl-herbert on Feb 03, 23 2115 13 GrandPa Page 22 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :