English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 22 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Gabs between lines no sticking on bed Von Ewolin on Jan 22, 23 1121 4 Ewolin Wizard stops at hot end after repair to destru... Von Diem on Jan 22, 23 1099 6 Lorenzo First layer issue. Can someone help me underst... Von Diem on Jan 22, 23 1370 2 Echo2112 Poor first layer and corner lifting Von Neophyl on Jan 21, 23 1454 5 ScottM Print Quality Von SG Newb Rider on Jan 21, 23 1024 2 3D_Design First layer showing lines in some parts Von Diem on Jan 20, 23 1083 2 Florian Extruder wiggle Von Crab on Jan 20, 23 1181 3 bjlled Layer "shifting" mid-print Von FoxRun3D on Jan 19, 23 3939 20 Bourbon Coffe... Can’t tighten Trapazoidal nuts. Von Erik Mitchell on Jan 19, 23 1292 1 Erik Mitchell Calibration issues Von karl-herbert on Jan 19, 23 1305 7 patrick91 Uneven first layers with gaps and blobs Von Diem on Jan 19, 23 1897 5 PolygonBaron x-end-motor R6 assembly Von Dik Harrison on Jan 18, 23 890 2 Dik Harrison What to try next to reduce stringing? Von MD on Jan 18, 23 22967 19 talz13 Blob removal - print problem! Von iftibashir on Jan 17, 23 1797 5 StirGlob Print Failing consistently about 1/8th inch up... Von RandyM9 on Jan 17, 23 978 2 Mr.Eastpond Issues after printer not being used for a whil... Von RandyM9 on Jan 16, 23 1363 3 billbail First layer Cal Issues Von JandLMak3rs on Jan 15, 23 1689 7 David Hickey Overheating Von JdL on Jan 15, 23 2162 15 JdL Trouble with taller prints Von jsw on Jan 15, 23 2290 17 paj418 Extruder skipping steps Von JoanTabb on Jan 14, 23 1113 2 Jordan Cornel... Seite 22 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: