English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 22 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author New kit printer burns PET-G at 250C Od R&D on Mar 01, 23 1755 5 Staszek Salik Poor quality sides throughout the model, rippl... Od Netpackrat on Feb 27, 23 2220 6 Stanislau Help with First prints Od chuck.gulotta on Feb 27, 23 2310 6 chuck.gulotta Problem printing PETG: Z-Level or something el... Od Thomas Lynch on Feb 22, 23 1817 2 prusausa Dragging, uneven 1st layer print Od Diem on Feb 22, 23 1718 3 skaddisbladis Gaps in corners Od Depz on Feb 21, 23 3014 2 Depz MK3+ Extruder body problem Od JMH714 on Feb 21, 23 2228 2 Pandamac First layer calibration and nozzle size Od Neophyl on Feb 21, 23 1899 2 tre4b First Project, spool jam and other issues Answered Od Robin on Feb 21, 23 2262 16 Ryan Print Creates Lip at Top Edge Od dhavener on Feb 18, 23 2561 1 dhavener Perimeter misalignment - Terrible surface fini... Od Serch-Aerobuil... on Feb 18, 23 1595 1 Serch-Aerobui... Odd XYZ Calibration Issue Answered Od Alex Wait on Feb 18, 23 2013 3 Alex Wait XYZ calibration failure Od Nimitz on Feb 17, 23 2099 3 Nimitz Another first layer problem. Od budgie on Feb 16, 23 2025 3 budgie Printing a replacement part, and minor 1st pri... Od RandyM9 on Feb 15, 23 2405 8 Culprit First layer - very unsatisfactory results Answered Od karl-herbert on Feb 14, 23 1976 4 skaddisbladis Test print looks a bit odd Od Diem on Feb 14, 23 2501 7 elan Fresh setup – continuous beeping Od Diem on Feb 13, 23 2781 4 Wolf Stringing worse than my ender 3 with same sett... Od danifrancescon on Feb 12, 23 3387 7 danifrancesco... First layer not constant in time Od gagou7 on Feb 12, 23 2165 5 gagou7 Stránka 22 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Share: