English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 211 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Replacing the X end motor-idler and tightening... Von thrawn86 on May 22, 18 2946 2 Oram & Ra... build plate Von LaPointe on May 21, 18 1601 2 mark.g22 XYZ calibration looks like it finds all 4 poin... Von jon.k on May 21, 18 3765 10 jon.k Filament Jam Von christian.m23 on May 21, 18 1974 10 christian.m23 Heat Bed Temperature Von Olef on May 21, 18 1928 4 Beech76 PETG cold pulls Von Gato on May 20, 18 28245 7 devilhunter Adhesion issues Von LaPointe on May 20, 18 2084 5 mark.m51 Use drill for assembly? Von Gato on May 20, 18 3254 9 Gato extruder clicks and leaves gaps in dispensed f... Von thrawn86 on May 20, 18 1938 4 dimprov Crash detected.. resumed with a layer shift. Von blueicee on May 19, 18 1266 5 dat1darkrai Severe Y-Axis Skipping/Shiftin Von Rosparovac on May 19, 18 1929 2 eric.s32 Help with troubleshooting failed prints Von Rosparovac on May 19, 18 2654 2 derek.f3 Filament Sensor not working Von Lups on May 19, 18 2169 3 Lups First Run xyz calibration trouble Von Webdad on May 19, 18 2199 8 chris.l21 Strange layer problem Von drkanukie on May 18, 18 1920 4 sven.m5 Y rods are not even after assembly Von Dreide on May 18, 18 3371 15 Manux XYZ calibration point crash Von reid.b on May 17, 18 1543 4 jeffrey.r3 Strange wall errors Von Lups on May 16, 18 1666 3 Lups Dat1darkrai's printer Von Ian B on May 16, 18 2734 15 dat1darkrai PLA filament "assaulted" the hot end... Von luca.r on May 16, 18 2184 5 luca.r Seite 211 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Teilen: