English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 195 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Layer shift? Bad filament? Da nathan0876 on Sep 06, 18 1658 2 RadTechDad HELP - Prints failing after using ABS Da Penwiggle on Sep 06, 18 2661 12 Penwiggle Better extruder adjustment design on the mk3? Da Neil Ramsay on Sep 06, 18 1892 4 Neil Ramsay RAMBo cover door (can't close?) Da Bigdogbro1 on Sep 05, 18 2781 15 toby.t3 Fails on the left/deep part of XY plane consis... Da ludovic.b2 on Sep 05, 18 1499 5 ludovic.b2 Failed Y on self test Da Kyle on Sep 04, 18 1390 2 Kyle Pinda Probe Connector or Board Connector is WR... Da Kai on Sep 04, 18 2804 4 will.h7 Finished assembly.. and printed flawlessly....... Da Christizzz on Sep 03, 18 1258 3 Christizzz Self test Y axis Length error Da Kyle on Sep 03, 18 3709 5 Symphy Just finished assembling my mk3..some.rattling... Da OPK on Sep 03, 18 1509 2 williamsryan.... Bad PLA adhesion only on small/curved models Da Daniele (Jolli... on Aug 31, 18 4868 8 Daniele (Joll... Calibration failed! Check axes and run again -... Da Kai on Aug 31, 18 3536 5 Penwiggle Layer Shift along y axis Da nathan0876 on Aug 31, 18 1399 2 Larry Cherry First layer PET shows a strange phenomenon Da JanV on Aug 29, 18 1268 1 JanV Problem Printing PETG Da scott.m25 on Aug 29, 18 3937 15 JerTheMaker Stringing and overall messing up print Da Emily.j on Aug 28, 18 2517 8 Emily.j Filament going down after prehot hotend Da stephen.h14 on Aug 28, 18 1853 7 sandro.c Problem FirstLayer Da RufusClupea on Aug 27, 18 2167 11 Sheoxs Replace the PEI sheet on the removable steel b... Da doa on Aug 27, 18 4491 18 Neil Ramsay First layer problem Da Bigdogbro1 on Aug 27, 18 2015 7 Jakub Pagina 195 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: