English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 195 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Layer shift? Bad filament? Par nathan0876 on Sep 06, 18 1658 2 RadTechDad HELP - Prints failing after using ABS Par Penwiggle on Sep 06, 18 2661 12 Penwiggle Better extruder adjustment design on the mk3? Par Neil Ramsay on Sep 06, 18 1892 4 Neil Ramsay RAMBo cover door (can't close?) Par Bigdogbro1 on Sep 05, 18 2781 15 toby.t3 Fails on the left/deep part of XY plane consis... Par ludovic.b2 on Sep 05, 18 1499 5 ludovic.b2 Failed Y on self test Par Kyle on Sep 04, 18 1390 2 Kyle Pinda Probe Connector or Board Connector is WR... Par Kai on Sep 04, 18 2804 4 will.h7 Finished assembly.. and printed flawlessly....... Par Christizzz on Sep 03, 18 1258 3 Christizzz Self test Y axis Length error Par Kyle on Sep 03, 18 3709 5 Symphy Just finished assembling my mk3..some.rattling... Par OPK on Sep 03, 18 1509 2 williamsryan.... Bad PLA adhesion only on small/curved models Par Daniele (Jolli... on Aug 31, 18 4868 8 Daniele (Joll... Calibration failed! Check axes and run again -... Par Kai on Aug 31, 18 3535 5 Penwiggle Layer Shift along y axis Par nathan0876 on Aug 31, 18 1399 2 Larry Cherry First layer PET shows a strange phenomenon Par JanV on Aug 29, 18 1268 1 JanV Problem Printing PETG Par scott.m25 on Aug 29, 18 3937 15 JerTheMaker Stringing and overall messing up print Par Emily.j on Aug 28, 18 2516 8 Emily.j Filament going down after prehot hotend Par stephen.h14 on Aug 28, 18 1852 7 sandro.c Problem FirstLayer Par RufusClupea on Aug 27, 18 2167 11 Sheoxs Replace the PEI sheet on the removable steel b... Par doa on Aug 27, 18 4491 18 Neil Ramsay First layer problem Par Bigdogbro1 on Aug 27, 18 2015 7 Jakub Page 195 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :