English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 193 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author First print tips Da John on Sep 20, 18 5164 9 John Layer shift in same place Da Kai on Sep 19, 18 1919 2 malthe.o The wizard isn't stopping and it's causing wei... Da toaf on Sep 19, 18 906 9 penguinmaster... Z Axis Calibration Da juan.e6 on Sep 18, 18 1468 3 juan.e6 Filament extrusion not consistent after Summer... Da Neal on Sep 18, 18 2121 7 jan.k57 mk3 with volcano not finding and calibrating Z Da roddy.n on Sep 18, 18 1580 5 roddy.n Print shifting Da Olef on Sep 18, 18 1397 3 mordechai.s X axis shifting Da dylan.m7 on Sep 17, 18 1101 1 dylan.m7 First print, PTFE tube came unseated... Da Kameron on Sep 17, 18 1423 12 Kameron Overhangs first layer Da surfgeorge on Sep 17, 18 3477 6 vinic More a Slicr3 issue than an extruder problem ? Da Jessie31 on Sep 17, 18 2548 13 Jessie31 Whistle first print question Da rob.l6 on Sep 17, 18 2541 2 TNcnc Under extrusion and clogging Da gronax on Sep 17, 18 9299 12 gronax New MK3 calibration issue Da Henry on Sep 17, 18 1305 4 Henry DIfferent layer heights Da Christizzz on Sep 16, 18 1650 7 stefan.p15 Is this Normal ? Da Christizzz on Sep 16, 18 2451 5 Christizzz LCD blinking after boot Da Koen Van Oost on Sep 16, 18 2245 4 Koen Van Oost 3rd print and extrude is making loud clicking ... Da daniel.m81 on Sep 14, 18 2008 6 daniel.m81 Will not pass Bed point calibration Da william.m50 on Sep 14, 18 1373 6 william.m50 0.25 Nozzle Problems Da bobstro on Sep 13, 18 6561 17 Matthias Pagina 193 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: