English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 180 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Is there an introduction to calibration docume... By Mustrum Ridcul... on Jan 11, 19 1535 3 jim.w15 Bed and Flexible Steel Sheet PEI with a little... By Bunny Science on Jan 11, 19 1569 2 maria.f2 MMU2 Problems with Filament Loading and Unload... By Rosparovac on Jan 11, 19 2091 2 reza.a Bed leveling issues Mk3 By thrawn86 on Jan 10, 19 1492 2 Billy Baldwin XY Issues (w pics) Pre-Assembled MK3 By CaptClearLeft on Jan 10, 19 1919 5 CaptClearLeft bumps By rob.l6 on Jan 10, 19 1400 4 armando.c2 Einsy Rambo board not sealed? By Olef on Jan 09, 19 1972 5 B Solar Issue with bottom left curling. This is after ... By lee.k5 on Jan 09, 19 2100 8 lee.k5 Extruder fail By JoanTabb on Jan 08, 19 2396 8 anthony.m26 HELP Selftest Error: Heater/Thermistor not con... By JoanTabb on Jan 08, 19 2680 3 roberts Y motor holder damaged during assembly By Chocki on Jan 07, 19 1858 5 Sorry Bed hot zone cable came out By Mustrum Ridcul... on Jan 06, 19 1524 2 TechDaddy First layer test looks okay, but can't print B... By jim.w15 on Jan 06, 19 6902 20 jim.w15 First Layer height variances By -- on Jan 05, 19 3562 14 dennis.s20 Infill issues By JoanTabb on Jan 05, 19 2178 7 gnat New build won't boot By JoanTabb on Jan 05, 19 2082 4 Milstream Sudden First Layer Problems By BRSlicer on Jan 05, 19 2641 6 BRSlicer Problem with XYZ calibration By JoanTabb on Jan 04, 19 2313 7 javier.s11 Can't figure out what the problem is with my f... By Skint007 on Jan 04, 19 2212 6 Skint007 Silver Filament Clogs Nozzle By Rosparovac on Jan 03, 19 2182 2 Helmut Page 180 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: