English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 174 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Potential warped bed? Da Dave Jackson on Feb 21, 19 1503 2 matthew.c59 Surface problems after reassembling the Extrud... Da thomas.s110 on Feb 21, 19 1325 4 thomas.s110 Power supply voltage Da DaJMasta on Feb 21, 19 3666 3 joaquin.o3 Bed Level Correction: Clarification of zones. Da -- on Feb 20, 19 769 4 GizmoGorilla Correct steps to remove jammed filament Da flioink on Feb 20, 19 3108 10 flioink Calibration Failed (Check Axes) at start of ca... Da Anzen on Feb 20, 19 2106 4 joel.p How long did assembly take Da hdhc on Feb 19, 19 14499 20 chad.k6 MK3 first print need some feedback Da john.m138 on Feb 19, 19 2160 5 john.m138 Difficulty with TPU Da Robin on Feb 19, 19 2393 11 STSanford y-rod-holder.stl Da -- on Feb 19, 19 2104 2 nsand U.S. source for spacers for the heatbed? Da kurzondax on Feb 18, 19 2264 12 kurzondax X Axis is way too loud? Da -- on Feb 18, 19 2901 5 Jaxel Mk3 Nozzle leaks after print begins Da -- on Feb 18, 19 1831 4 zjdoliver Change in wall thickness after each change in ... Da Peter M on Feb 17, 19 2308 10 The M Printer prints nice first layer but later get ... Da Peter M on Feb 17, 19 1629 3 MilSen18 Printing new MK3s parts Da Nikolai on Feb 16, 19 1476 2 matthew.m63 Constant clogging Da 3Delight on Feb 16, 19 10599 9 tony.t3 Assembly question: Filament sensor cover Da 3Delight on Feb 16, 19 1586 4 vernon1xx Upgrade manual MK3 to MK3s Da Migamix on Feb 16, 19 2128 3 Paul_Wilts MK3S print colour Da Nikolai on Feb 15, 19 1306 4 Neil Ramsay Pagina 174 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: