English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 165 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Print detaching issues Da toaf on Apr 11, 19 2929 3 RF XY Calibration Problem Da -- on Apr 11, 19 1792 2 jt.t Am I damaging my build plate? Da vintagepc on Apr 11, 19 1560 4 reilly.s Build plate already damaged? Da Mustrum Ridcul... on Apr 11, 19 2622 9 spencer.b5 extuder catching on own print Da Mustrum Ridcul... on Apr 11, 19 1973 3 Yallop Y-Axis Shifting During First Layer Da -- on Apr 10, 19 1946 8 awoodbridge Printing issues Da suki.d on Apr 10, 19 1995 3 suki.d Need some help for bad printing Da Filnet on Apr 09, 19 1432 4 Filnet MK3S Kit Z Calibration Not Moving Da andrew.j15 on Apr 09, 19 2781 15 steven.w24 Unable to run the Calibration Menu’s First Lay... Da arkowal4 on Apr 09, 19 1586 2 arkowal4 mk3s stops printing halfway when using prusa s... Da -- on Apr 08, 19 1847 4 zen.k Newbie: Prints GOOD, except first 3-4 layers?? Da redherring9 on Apr 08, 19 2097 8 redherring9 Dimensional accuracy requirement of Prusa prin... Da RetireeJay on Apr 07, 19 1966 3 Sravan Mettup... MK3S upgrade to IR sensor unable to calibrate Da Mustrum Ridcul... on Apr 07, 19 2114 4 Valiran New Assembly, Unable to Connect via Pronterfac... Da Mustrum Ridcul... on Apr 07, 19 1868 2 C. O. Z-Calibration Failure after Originially Workin... Da -- on Apr 06, 19 2565 10 Lumbermouth PTFE Tube on Hotend Assembly too long? Da Grandpa Joe on Apr 05, 19 4184 6 daniel.e24 assembling year old MK3 kit: anything to updat... Da Sravan Mettupa... on Apr 05, 19 2391 14 Sravan Mettup... Left hotend fan? Spinning, Not Spinning? MK3 Da fuco on Apr 05, 19 11916 24 michael.p77 Z axis belt alignment. Da Kai on Apr 04, 19 876 4 william.a12 Pagina 165 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: