English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 165 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Printing issues Przez suki.d on Apr 10, 19 1901 3 suki.d Need some help for bad printing Przez Filnet on Apr 09, 19 1371 4 Filnet MK3S Kit Z Calibration Not Moving Przez andrew.j15 on Apr 09, 19 2707 15 steven.w24 Unable to run the Calibration Menu’s First Lay... Przez arkowal4 on Apr 09, 19 1534 2 arkowal4 mk3s stops printing halfway when using prusa s... Przez -- on Apr 08, 19 1748 4 zen.k Newbie: Prints GOOD, except first 3-4 layers?? Przez redherring9 on Apr 08, 19 2033 8 redherring9 Dimensional accuracy requirement of Prusa prin... Przez RetireeJay on Apr 07, 19 1908 3 Sravan Mettup... MK3S upgrade to IR sensor unable to calibrate Przez Mustrum Ridcul... on Apr 07, 19 2037 4 Valiran New Assembly, Unable to Connect via Pronterfac... Przez Mustrum Ridcul... on Apr 07, 19 1816 2 C. O. Z-Calibration Failure after Originially Workin... Przez -- on Apr 06, 19 2393 10 Lumbermouth PTFE Tube on Hotend Assembly too long? Przez Grandpa Joe on Apr 05, 19 4043 6 daniel.e24 assembling year old MK3 kit: anything to updat... Przez Sravan Mettupa... on Apr 05, 19 2348 14 Sravan Mettup... Left hotend fan? Spinning, Not Spinning? MK3 Przez fuco on Apr 05, 19 11628 24 michael.p77 Z axis belt alignment. Przez Kai on Apr 04, 19 845 4 william.a12 First layer creates wavy uneven lines Przez bobstro on Apr 03, 19 3305 2 damion fusco Problems with very new printer (DIY KIT) Przez holmes4 on Apr 03, 19 2215 11 Merinto Oh look another stripped grub screw post Przez -- on Apr 03, 19 4287 15 matt.b28 Filament bends around the nozzle Przez Desti on Apr 02, 19 2280 6 Desti Can someone help me with what I may have set w... Przez bobstro on Apr 02, 19 1947 9 jack.c5 Warped Y frame or Heatbed? Przez -- on Apr 02, 19 2239 2 nubbyninja Strona 165 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: