English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 134 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Bad Top Layer - Benchy vs Part Przez proleland on Dec 29, 19 4251 2 proleland First layer looks always horrible in the middl... Przez friedemann on Dec 28, 19 4409 4 friedemann X axis shift while homing - Odd issue that I c... Przez cvjrod on Dec 26, 19 4610 12 3dweltan Powder coated bed not working well Przez cwbullet on Dec 25, 19 1824 4 lembo First layer areas with different heights Answered Przez JoanTabb on Dec 25, 19 2052 6 CE Built the machine, but when I do the first lay... Przez Ken G. on Dec 24, 19 9267 30 Ken G. bed temperature regulation problems Przez JoanTabb on Dec 24, 19 1483 3 cdg3dprinting First layer calibration and Filament ooze Answered Przez AeroNerd on Dec 24, 19 2689 7 AeroNerd Constant preheat and thermal runaway errors! Przez PrinterGuy74 on Dec 24, 19 1964 3 PrinterGuy74 possible nozzle clog? Przez bobstro on Dec 22, 19 1576 2 Andy Y-AXIS CALIBRATION PROBLEM Przez wbDheartG on Dec 21, 19 4373 3 wbDheartG XYZ Dimensional Error Przez Mike Daneman on Dec 19, 19 1554 2 michael.h5 Printer not extruding enough filament, results... Przez simon-2 on Dec 19, 19 4127 8 simon-2 Filament sensor always active Przez JoanTabb on Dec 18, 19 1781 4 raul Missing parts for MK3S build at #7, Heatbed an... Przez Olef on Dec 18, 19 1858 3 AL Dev New MK3S - Staircasing/Y Axis Issue Przez shad0wth3fall3... on Dec 18, 19 2554 4 shad0wth3fall... [Build Problems] E-Exis FS-Cover Assembly Issu... Przez rmm200 on Dec 17, 19 2828 9 CAR Extruder clicking and not feeding Przez Mr Disintegrat... on Dec 17, 19 2357 4 Mr Disintegra... Possible Y-Axis belt tightening under spec Przez crazycabo350 on Dec 17, 19 1813 3 crazycabo350 Consistent Filament Excrusion Przez fwcox on Dec 16, 19 1709 2 fwcox Strona 134 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: