English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 134 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Bad Top Layer - Benchy vs Part Por proleland on Dec 29, 19 4255 2 proleland First layer looks always horrible in the middl... Por friedemann on Dec 28, 19 4426 4 friedemann X axis shift while homing - Odd issue that I c... Por cvjrod on Dec 26, 19 4614 12 3dweltan Powder coated bed not working well Por cwbullet on Dec 25, 19 1827 4 lembo First layer areas with different heights Answered Por JoanTabb on Dec 25, 19 2056 6 CE Built the machine, but when I do the first lay... Por Ken G. on Dec 24, 19 9285 30 Ken G. bed temperature regulation problems Por JoanTabb on Dec 24, 19 1494 3 cdg3dprinting First layer calibration and Filament ooze Answered Por AeroNerd on Dec 24, 19 2699 7 AeroNerd Constant preheat and thermal runaway errors! Por PrinterGuy74 on Dec 24, 19 1965 3 PrinterGuy74 possible nozzle clog? Por bobstro on Dec 22, 19 1579 2 Andy Y-AXIS CALIBRATION PROBLEM Por wbDheartG on Dec 21, 19 4378 3 wbDheartG XYZ Dimensional Error Por Mike Daneman on Dec 19, 19 1560 2 michael.h5 Printer not extruding enough filament, results... Por simon-2 on Dec 19, 19 4143 8 simon-2 Filament sensor always active Por JoanTabb on Dec 18, 19 1789 4 raul Missing parts for MK3S build at #7, Heatbed an... Por Olef on Dec 18, 19 1868 3 AL Dev New MK3S - Staircasing/Y Axis Issue Por shad0wth3fall3... on Dec 18, 19 2556 4 shad0wth3fall... [Build Problems] E-Exis FS-Cover Assembly Issu... Por rmm200 on Dec 17, 19 2848 9 CAR Extruder clicking and not feeding Por Mr Disintegrat... on Dec 17, 19 2365 4 Mr Disintegra... Possible Y-Axis belt tightening under spec Por crazycabo350 on Dec 17, 19 1815 3 crazycabo350 Consistent Filament Excrusion Por fwcox on Dec 16, 19 1716 2 fwcox Página 134 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: