English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 127 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Oversized Holes Da rmm200 on Mar 18, 20 3484 5 pmcgarr First layer calibration not going well. How do... Answered Da Steve on Mar 17, 20 3211 4 creakesiv First Layer Tearing at Intersections Answered Da AxioN on Mar 17, 20 2360 5 AxioN What is the purpose of the nylon filament? Da rmm200 on Mar 16, 20 9202 3 HolgerW Base of tree frog Da Cliff A on Mar 15, 20 2634 3 Cliff A MK3->MK3/S Upgrade: Forgot to Remove Filament Da Ryan Rosario on Mar 14, 20 1698 1 Ryan Rosario Test print (logo) & 1st print ok but now print... Da Nimitz on Mar 14, 20 3267 16 Nimitz Prusa Kit First Print Difficulties, Ready to g... Da rmm200 on Mar 13, 20 2499 7 JT What is this wire, wizzard fail Da Knickohr on Mar 13, 20 2066 3 atomleef Bumpy Surfaces Da rmm200 on Mar 12, 20 1775 2 achaney91 X Axis not smooth to the left Da Agkirk on Mar 12, 20 4548 4 Benjamin What is this wire, wizzard fail Da karl-herbert on Mar 12, 20 1893 2 atomleef Bondtech Mk3s2 nightmare Da Rev Mindbender on Mar 11, 20 2054 4 Rev Mindbende... Self Test fail: X and Y pulleys different? Da Texy on Mar 11, 20 4299 6 Dave Selftest error: Heater/Thermistor Da Daniel on Mar 11, 20 1896 1 Daniel Slightly misaligned layers Da Robb on Mar 11, 20 2161 1 Robb First Layer/Maybe Filament Issue Da amish_rabbi on Mar 11, 20 1708 2 amish_rabbi X-Axis is scaled down Da Neophyl on Mar 10, 20 2176 4 Adi Upgrade from MK3 to MK3S - bad print quality Da vintagepc on Mar 08, 20 2659 3 UFO Calibration Works - First Layer Appears Good -... Da jmanley on Mar 08, 20 3080 9 jmanley Pagina 127 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Condividi: