English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 114 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Electronics relocation Por Neodev on Jun 01, 20 7529 16 Granny Pre-heating Gcode due to excessive extrusion Por Loak on May 31, 20 2396 2 nirv27 Curious about a noise - is it normal? Por Chris P on May 30, 20 1846 4 Chris P MK3S Kit > Selftest after assembly > Error X (... Por viehhausen5 on May 30, 20 1758 3 viehhausen5 new MK3s kit assembled but hotbed issues Answered Por pwiltsey on May 30, 20 2290 5 pwiltsey Temperature drop after first layer Por Francisco on May 29, 20 5038 11 Muji3D A Ghost of boaty in the first layer?! Por bobstro on May 29, 20 2342 3 Lord Radford Should the power switch light up? Por With_Maltodext... on May 29, 20 3799 13 Andrew P.I.N.D.A Probe setting with Zip tie technique... Por Neophyl on May 29, 20 3541 6 luvology First layer issues Por Neophyl on May 29, 20 2818 9 dcs13579 FLEX stuck in the hotend Por rmm200 on May 28, 20 2930 9 Matt Boyer Cant seem to get proper consistent prints 🙁 -... Por FerTech on May 27, 20 2810 13 FerTech First Layer 1.2mm nozzle "imperfections" Por bobstro on May 27, 20 3822 3 DKern Cascade failure Answered Por Peter in Katy on May 27, 20 2502 6 daniel-9 Printer Crash During Build - Y-axis will not p... Por rmm200 on May 27, 20 2695 7 Andy Ruth Inconsistent first layers Por CovertPluto350... on May 26, 20 2297 2 CovertPluto35... First print ever help! Por gman on May 26, 20 2028 9 Aquarian Little filament print - Mass Contractions Moto... Por Andrew on May 26, 20 2553 9 f.otto Leaking hotend/heat break/heat block assembly Por Neophyl on May 26, 20 9540 5 Jiheffe How to raise extruder before first print? Por Parallax on May 25, 20 1841 2 Parallax Página 114 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: