English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 114 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Rotating the hotend? Od XabuJr on Jun 02, 20 3730 4 XabuJr i3 Mk3S: extruder click, click noise when prin... Od Werner on Jun 02, 20 1650 1 Werner First Layer Cal Od Cynan on Jun 02, 20 1924 3 Gonz IOS Extruder heater socket on Rambo board backward... Od lactose on Jun 01, 20 1900 1 lactose New printer fun to build. Od Mike on Jun 01, 20 3034 15 Mike Adhesion or lifting issue in some places - fir... Od DamienB on Jun 01, 20 1876 3 mgtarallo New prusa, pre-assembled, very unimpressed, no... Od cwbullet on Jun 01, 20 2431 7 axfelix MK3S bed wobble/strong y vibrations Od Cynan on Jun 01, 20 3618 4 Stanisław Electronics relocation Od Neodev on Jun 01, 20 7790 16 Granny Pre-heating Gcode due to excessive extrusion Od Loak on May 31, 20 2547 2 nirv27 Curious about a noise - is it normal? Od Chris P on May 30, 20 2003 4 Chris P MK3S Kit > Selftest after assembly > Error X (... Od viehhausen5 on May 30, 20 1968 3 viehhausen5 new MK3s kit assembled but hotbed issues Answered Od pwiltsey on May 30, 20 2435 5 pwiltsey Temperature drop after first layer Od Francisco on May 29, 20 5424 11 Muji3D A Ghost of boaty in the first layer?! Od bobstro on May 29, 20 2560 3 Lord Radford Should the power switch light up? Od With_Maltodext... on May 29, 20 4060 13 Andrew P.I.N.D.A Probe setting with Zip tie technique... Od Neophyl on May 29, 20 3835 6 luvology First layer issues Od Neophyl on May 29, 20 3075 9 dcs13579 FLEX stuck in the hotend Od rmm200 on May 28, 20 3217 9 Matt Boyer Cant seem to get proper consistent prints 🙁 -... Od FerTech on May 27, 20 3049 13 FerTech Stránka 114 / 218 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Další Share: