English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 114 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Extruder heater socket on Rambo board backward... Von lactose on Jun 01, 20 1857 1 lactose New printer fun to build. Von Mike on Jun 01, 20 2925 15 Mike Adhesion or lifting issue in some places - fir... Von DamienB on Jun 01, 20 1850 3 mgtarallo New prusa, pre-assembled, very unimpressed, no... Von cwbullet on Jun 01, 20 2383 7 axfelix MK3S bed wobble/strong y vibrations Von Cynan on Jun 01, 20 3539 4 Stanisław Electronics relocation Von Neodev on Jun 01, 20 7725 16 Granny Pre-heating Gcode due to excessive extrusion Von Loak on May 31, 20 2473 2 nirv27 Curious about a noise - is it normal? Von Chris P on May 30, 20 1957 4 Chris P MK3S Kit > Selftest after assembly > Error X (... Von viehhausen5 on May 30, 20 1887 3 viehhausen5 new MK3s kit assembled but hotbed issues Answered Von pwiltsey on May 30, 20 2400 5 pwiltsey Temperature drop after first layer Von Francisco on May 29, 20 5344 11 Muji3D A Ghost of boaty in the first layer?! Von bobstro on May 29, 20 2511 3 Lord Radford Should the power switch light up? Von With_Maltodext... on May 29, 20 3999 13 Andrew P.I.N.D.A Probe setting with Zip tie technique... Von Neophyl on May 29, 20 3755 6 luvology First layer issues Von Neophyl on May 29, 20 2993 9 dcs13579 FLEX stuck in the hotend Von rmm200 on May 28, 20 3151 9 Matt Boyer Cant seem to get proper consistent prints 🙁 -... Von FerTech on May 27, 20 3002 13 FerTech First Layer 1.2mm nozzle "imperfections" Von bobstro on May 27, 20 4029 3 DKern Cascade failure Answered Von Peter in Katy on May 27, 20 2728 6 daniel-9 Printer Crash During Build - Y-axis will not p... Von rmm200 on May 27, 20 2897 7 Andy Ruth Seite 114 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Teilen: