Avisos
Vaciar todo

Three years and still going strong......  

  RSS
BertUK
(@bertuk)
Eminent Member
Three years and still going strong......

So, I am getting close to nearly 3 years of owning my Prusa Mini – the original one. And still loving the little machine. It has been printing nearly daily and produced lots and lots of lovely prints. Yes, some teething problems but very stable since. Only replaced the bearings and once, the nozzle (actually not needed).  Beyond that pretty much bog standard. I bought lots and lots of spare parts (at the beginning of lockdown, just in case) but have not used them. I have now been printing for at least 9 months without having to adjust the extruder. Impressive. Prusa, well done!

Original Prusa Mini 03/20 PINDAR Misumi Bearings

Respondido : 13/02/2023 1:28 pm
languer me gusta
TeachThePrints
(@teachtheprints)
Estimable Member
RE: Three years and still going strong......

Teach us your skills please. 

I have to take apart the extruder after every swap from PLA to PETG and vice-versa, since it results in clogged nozzles. 

Prusa Mini FW4.4.1

Respondido : 16/02/2023 11:35 am
Diem
 Diem
(@diem)
Illustrious Member

after every swap from PLA to PETG and vice-versa, since it results in clogged nozzles. 

Always complete the change and flush at the higher of the two temperatures, then cool to print if necessary.

Cheerio,

 

Respondido : 16/02/2023 11:50 am
languer y mark me gusta
BertUK
(@bertuk)
Eminent Member
Topic starter answered:
RE:

Strange. I can switch between filaments without any problem. Only thing I do AFTER PC blend printing is feeding the next filament (PLA/PETG) at a high temperature through the extruder for a few seconds to clear the PC. Amazing little machine......

Esta publicación ha sido modificada el hace 12 months por BertUK

Original Prusa Mini 03/20 PINDAR Misumi Bearings

Respondido : 30/03/2023 10:47 am
mark me gusta
cwbullet
(@cwbullet)
Miembro
RE: Three years and still going strong......

I have four and on two I have had to replace the hotend.  

--------------------
Chuck H
3D Printer Review Blog

Respondido : 30/03/2023 10:54 am
BertUK
(@bertuk)
Eminent Member
Topic starter answered:
RE: Three years and still going strong......

Now FOUR years........ fitted a wi-fi module last summer and re-greased the bearings but beyond that all still as standard as can be! Nothing replaced. Nothing fixed.  Runs amazingly well with the Input Shape software. Printing with PLA, PETG, Flex and PC without any issues. What can I say....... amazing little machine!   Statistics: total filament length printed: 5.1km - printing time: 73 days! I have all the parts to do an overhaul but 'if it ain't broke.......'

Original Prusa Mini 03/20 PINDAR Misumi Bearings

Respondido : 26/02/2024 5:15 pm
Bob
 Bob
(@bob-2)
Reputable Member
RE: Three years and still going strong......

Glad to hear it.  I have an early mini also, not the first batch, there was a delay in shipping for awhile after the first batch went out, so mine's second batch.  I don't run mine everyday and I did change out the heat break to stop the clogging, but it's been a pretty nice printer. 

Cheers

-Bob

Prusa I3 Mk2 kit upgraded to Mk2.5s, Ender3 with many mods, Prusa Mini kit with Bondtech heat break, Prusa I3 Mk3s+ kit

Respondido : 27/02/2024 8:07 pm
Compartir: