English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Page 155 / 196 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Suivant Titre du sujet Dernier message Nombre de vues Messages Author First layer Par Frans Krau on May 23, 20 2428 2 kenatno10 older version of prusaslicer Par bobstro on May 22, 20 10142 10 tpsmidsltd Unlocked Firmware Par bobstro on May 22, 20 3566 4 jim Problems with first layer of supports Par bobstro on May 22, 20 2562 2 katharine.p2 Sudden X or Y shifts Par BobinAtlanta on May 21, 20 2357 3 BobinAtlanta Bellus3D Face Mask Fitter for COVID-19 Par ChristinaR on May 20, 20 3089 5 ChristinaR Review: PolyMaker PolyBox Par cwbullet on May 20, 20 6899 1 cwbullet Possible underextrusion Par Emily on May 19, 20 1805 3 Emily Mask out a section of printing DURING a print Par 3DALHEMIJA on May 18, 20 1839 2 Mat What's the problem with moisture? Par Paul on May 18, 20 5730 8 RedDawg self introduction Par jiangann34 on May 18, 20 1798 1 jiangann34 What filament/material can be used in the mout... Par educa on May 17, 20 7175 5 Chris P cxbcvxcvxcv Par free~Watch!! T... on May 15, 20 1604 1 free~Watch!! ... Leveling-Free of upcoming new Creality. How do... Par Vincenzo.c3 on May 14, 20 3121 9 Vincenzo.c3 Alternative textured PEI sheet? Par bobstro on May 14, 20 4506 10 Pat Erickson How to make a standing coin shaped object roun... Par bobstro on May 14, 20 2380 3 prusanewuser Why PETG bracket broke easily? Par prusanewuser on May 13, 20 8958 10 prusanewuser 3D newbie : Question about designing an object... Par Neophyl on May 12, 20 2164 4 ilja 3D newbie : What type of filament to buy along... Par ilja on May 12, 20 4816 4 ilja What parameters for support materials when pri... Par Dave J on May 12, 20 2826 6 prusanewuser Page 155 / 196 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Suivant Partager :