English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Page 154 / 195 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Suivant Titre du sujet Dernier message Nombre de vues Messages Author good slicing software? Par bobstro on May 31, 20 3370 4 layden_blackw... How does Prusament PETG behave under acetone v... Par Crawlerin on May 31, 20 2708 3 prusanewuser 3d print services Par kelleyhicks197... on May 30, 20 2938 4 towlerg MKS GEN-2Z V1.2 vs MKS V1.4 Par shmuelgonen on May 29, 20 3357 1 shmuelgonen Raspberry Pi 4B 8 GB Par karl-herbert on May 28, 20 2535 3 rmm200 Polyalchemy producing again? Par Jacob Kinchelo... on May 28, 20 2176 4 Jacob Kinchel... Prusament Quality Control Par Sam_PNW on May 27, 20 7145 22 debra.k Help: Suggested Test Prints Par cwbullet on May 27, 20 2220 6 cwbullet Make your 3D prints stronger with titanium rod... Par cwbullet on May 27, 20 2438 2 coolRR bed adhesion ? Par Neophyl on May 27, 20 1729 2 layden_blackw... Slicr3D Best Infill Par Grandpa Joe on May 26, 20 2278 1 Grandpa Joe 9 suggestions for Original Prusa i3 MK4 Par CovertPluto350... on May 26, 20 2984 3 CovertPluto35... Prusament PC Blend Par 3D Printing Sc... on May 26, 20 4426 6 nic Heat bed sensor problem Par keelanforrests on May 25, 20 2711 9 kevin.k33 First layer Par Frans Krau on May 23, 20 2427 2 kenatno10 older version of prusaslicer Par bobstro on May 22, 20 10132 10 tpsmidsltd Unlocked Firmware Par bobstro on May 22, 20 3564 4 jim Problems with first layer of supports Par bobstro on May 22, 20 2561 2 katharine.p2 Sudden X or Y shifts Par BobinAtlanta on May 21, 20 2356 3 BobinAtlanta Bellus3D Face Mask Fitter for COVID-19 Par ChristinaR on May 20, 20 3089 5 ChristinaR Page 154 / 195 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Suivant Partager :