English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Strona 154 / 195 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Następny Tytuł Tematu Ostatni Post Widok Posty Author Harmonised code for 3D printed parts? Przez Ben_Love on May 31, 20 5876 3 Ben_Love good slicing software? Przez bobstro on May 31, 20 3371 4 layden_blackw... How does Prusament PETG behave under acetone v... Przez Crawlerin on May 31, 20 2708 3 prusanewuser 3d print services Przez kelleyhicks197... on May 30, 20 2939 4 towlerg MKS GEN-2Z V1.2 vs MKS V1.4 Przez shmuelgonen on May 29, 20 3357 1 shmuelgonen Raspberry Pi 4B 8 GB Przez karl-herbert on May 28, 20 2535 3 rmm200 Polyalchemy producing again? Przez Jacob Kinchelo... on May 28, 20 2177 4 Jacob Kinchel... Prusament Quality Control Przez Sam_PNW on May 27, 20 7148 22 debra.k Help: Suggested Test Prints Przez cwbullet on May 27, 20 2221 6 cwbullet Make your 3D prints stronger with titanium rod... Przez cwbullet on May 27, 20 2439 2 coolRR bed adhesion ? Przez Neophyl on May 27, 20 1729 2 layden_blackw... Slicr3D Best Infill Przez Grandpa Joe on May 26, 20 2278 1 Grandpa Joe 9 suggestions for Original Prusa i3 MK4 Przez CovertPluto350... on May 26, 20 2984 3 CovertPluto35... Prusament PC Blend Przez 3D Printing Sc... on May 26, 20 4428 6 nic Heat bed sensor problem Przez keelanforrests on May 25, 20 2719 9 kevin.k33 First layer Przez Frans Krau on May 23, 20 2427 2 kenatno10 older version of prusaslicer Przez bobstro on May 22, 20 10133 10 tpsmidsltd Unlocked Firmware Przez bobstro on May 22, 20 3565 4 jim Problems with first layer of supports Przez bobstro on May 22, 20 2561 2 katharine.p2 Sudden X or Y shifts Przez BobinAtlanta on May 21, 20 2356 3 BobinAtlanta Strona 154 / 195 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 Następny Share: