English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Page 155 / 196 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Next Topic Title Last Post Views Posts Author Polyalchemy producing again? By Jacob Kinchelo... on May 28, 20 2191 4 Jacob Kinchel... Prusament Quality Control By Sam_PNW on May 27, 20 7204 22 debra.k Help: Suggested Test Prints By cwbullet on May 27, 20 2235 6 cwbullet Make your 3D prints stronger with titanium rod... By cwbullet on May 27, 20 2458 2 coolRR bed adhesion ? By Neophyl on May 27, 20 1737 2 layden_blackw... Slicr3D Best Infill By Grandpa Joe on May 26, 20 2293 1 Grandpa Joe 9 suggestions for Original Prusa i3 MK4 By CovertPluto350... on May 26, 20 3012 3 CovertPluto35... Prusament PC Blend By 3D Printing Sc... on May 26, 20 4448 6 nic Heat bed sensor problem By keelanforrests on May 25, 20 2736 9 kevin.k33 First layer By Frans Krau on May 23, 20 2447 2 kenatno10 older version of prusaslicer By bobstro on May 22, 20 10203 10 tpsmidsltd Unlocked Firmware By bobstro on May 22, 20 3582 4 jim Problems with first layer of supports By bobstro on May 22, 20 2575 2 katharine.p2 Sudden X or Y shifts By BobinAtlanta on May 21, 20 2366 3 BobinAtlanta Bellus3D Face Mask Fitter for COVID-19 By ChristinaR on May 20, 20 3106 5 ChristinaR Review: PolyMaker PolyBox By cwbullet on May 20, 20 6958 1 cwbullet Possible underextrusion By Emily on May 19, 20 1821 3 Emily Mask out a section of printing DURING a print By 3DALHEMIJA on May 18, 20 1847 2 Mat What's the problem with moisture? By Paul on May 18, 20 5855 8 RedDawg self introduction By jiangann34 on May 18, 20 1802 1 jiangann34 Page 155 / 196 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Next Share: