English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum General discussion, announcements and releases Notifications Clear all General discussion, announcements and releases | RSS Strona 153 / 196 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Następny Tytuł Tematu Ostatni Post Widok Posty Author Why circular holes are not circular? Which pla... Przez prusanewuser on Jun 13, 20 8153 17 prusanewuser Consistent crashing since new firmware update Przez DayOutBreeze on Jun 13, 20 2013 3 DayOutBreeze Prusa slicer on raspberry pi 4 (4GB) Przez cliffmedina007 on Jun 12, 20 10979 8 peter.h16 Orientation upon importing to Prusa Slicer Przez Neophyl on Jun 09, 20 3127 3 prusanewuser Shipping delay Przez CCJack on Jun 09, 20 10974 24 Joeri What to do while I wait? Przez Crawlerin on Jun 08, 20 3012 5 nodaysoff360 Is the Orange PLA different than Prusament Ora... Przez Crawlerin on Jun 08, 20 3253 3 Matt Boyer Prusament Design Challenge Przez Matt Boyer on Jun 08, 20 3087 13 Matt Boyer 9 suggestions for Original Prusa i3 MK4 ? Przez CovertPluto350... on Jun 07, 20 3182 3 edgarismaelei... prints not sticking to bed Przez lindley5 on Jun 07, 20 1861 4 lindley5 Post printing processing Przez mark_glasson on Jun 07, 20 1634 2 towlerg What should I buy? Przez K7ZPJ on Jun 07, 20 2101 2 tony.chronopo... Slicing issue with 2.2.0 Przez JoanTabb on Jun 06, 20 1836 2 bludrgn2000 Anet E16 Profile Przez bobstro on Jun 06, 20 2519 2 Craig G Better surface above support? Przez gero on Jun 05, 20 1771 1 gero Having decided to buy. Przez zinefer on Jun 05, 20 5311 23 Flyntlock print on demand setup? Answered Przez Bo Herrmannsen on Jun 05, 20 2358 3 Bo Herrmannse... Can't get slicer to create supports in some pl... Przez steve.b37 on Jun 05, 20 1848 1 steve.b37 BRAun NTF3000 Thermometer - $20 usd Przez omardeniko on Jun 05, 20 1901 1 omardeniko Printing defect. Przez Adrian on Jun 04, 20 1798 2 Adrian Strona 153 / 196 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 Następny Share: