Notifiche
Cancella tutti

Hall of Shame  

Pagina 1 / 4
  RSS
cwbullet
(@cwbullet)
Utenti
Hall of Shame

Post you awesome failures in 3D Printing in this thread.  

Below is one of mine.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 19/05/2021 2:53 pm
UjinDesign e hanno apprezzato
Baklin
(@baklin)
Reputable Member
RE: Hall of Shame

I'm sure everyone has some like these.

Postato : 20/05/2021 8:16 am
tsingi, Lemsko, Bullseye3d e 3 persone hanno apprezzato
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

@baklin

Yup that is a good one.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 20/05/2021 10:32 am
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

Yellow Poo  th

I simply refer to this as yellow poo.  What you have to have n your diet to get this?

Attachment removed

--------------------
Chuck H
3D Printer Review Blog

Postato : 20/05/2021 10:38 am
AnnieR hanno apprezzato
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

The blob is coming to get you!

--------------------
Chuck H
3D Printer Review Blog

Postato : 21/05/2021 5:04 pm
Prusa Fanatic, R3V3RS3R e Bullseye3d hanno apprezzato
Baklin
(@baklin)
Reputable Member
RE: Hall of Shame

I'm so glad this never happened to me (so far)

Postato : 21/05/2021 7:23 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

@baklin

Eventually, it happens to all of us.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 21/05/2021 7:58 pm
Alid hanno apprezzato
Clarmrrsn
(@clarmrrsn)
Honorable Member
RE: Hall of Shame
Posted by: @cwbullet

Yellow Poo  th

I simply refer to this as yellow poo.  What you have to have n your diet to get this?

Attachment removed

That looks like a jellyfish turd!

Tank you very much!

Postato : 21/05/2021 8:59 pm
jsw e Aphaitas hanno apprezzato
Clarmrrsn
(@clarmrrsn)
Honorable Member
RE: Hall of Shame

PS I learnt a valuable lesson a few weeks ago.

Don't place narrow rods on the inside of a ring, brims don't work on the inside of a solid ring and will result in a hotend of doom when they detatch from the bed.

My camera helped me notice it and stop before it turned into  a wombat poop of death!!

Tank you very much!

Postato : 21/05/2021 9:02 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame
Posted by: @clarmrrsn
Posted by: @cwbullet

Yellow Poo  th

I simply refer to this as yellow poo.  What you have to have n your diet to get this?

Attachment removed

That looks like a jellyfish turd!

Maybe it is a Rorschach Test!  You see what you want to see.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 21/05/2021 10:02 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

@clarmrrsn

Yup.  I rarely have a disaster because I catch them on the camera too, but when I do they are impressive.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 21/05/2021 10:03 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

Best Q ASA will just not stick!

--------------------
Chuck H
3D Printer Review Blog

Postato : 22/05/2021 12:34 am
Tu hanno apprezzato
scaldinghotcarl
(@scaldinghotcarl)
Active Member
RE: Hall of Shame

Postato : 11/07/2021 5:04 pm
scaldinghotcarl
(@scaldinghotcarl)
Active Member
RE: Hall of Shame

@cwbullet

How did you clean this up?

Postato : 11/07/2021 5:05 pm
JoanTabb
(@joantabb)
Veteran Member Moderator
RE: Hall of Shame

I use a soldering iron to pare the Blob away from the wires of the thermistor and heater

and use nozzle heat to heat from the inside

regards Joan

I try to make safe suggestions,You should understand the context and ensure you are happy that they are safe before attempting to apply my suggestions, what you do, is YOUR responsibility. Location Halifax UK

Postato : 11/07/2021 6:04 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
RE: Hall of Shame

@scaldinghotcarl

I have a heat gun.  It all came off with tweezers.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 12/07/2021 1:15 am
EdgeSync
(@edgesync)
Active Member
Spaghetti Monster Ahoy

 

One of my worst to date. Tried printing Nefertiti overnight shortly after I built my printer. At least it didn't blob all over the hotend 🙂

Postato : 22/10/2021 1:06 pm
cwbullet
(@cwbullet)
Utenti
Topic starter answered:
Goodnone

That is a good one.  

--------------------
Chuck H
3D Printer Review Blog

Postato : 22/10/2021 1:07 pm
karl-herbert
(@karl-herbert)
Illustrious Member
RE: Spaghetti Monster Ahoy

truly a monstrous spaghetti work of art. I hope your printer survived without any damage 👍 

wbr,

Karl

Statt zu klagen, dass wir nicht alles haben, was wir wollen, sollten wir lieber dankbar sein, dass wir nicht alles bekommen, was wir verdienen.

Postato : 22/10/2021 5:43 pm
Matt Boyer
(@matt-boyer)
Estimable Member
RE: Hall of Shame

I had this fantasy that I could build my MK3 and print a perfect benchy straight away.  In reality, it took me about 11 hours to assemble and I finished at 2am.  Still holding onto the fantasy I fired off the boat and watched the first couple layers go down.  Well, I had a lot to learn about what a good first layer looks like because the print popped off right after I walked away and went to bed.  When I woke up my fantasy had turned to spaghetti.

Postato : 28/01/2022 9:23 pm
R3V3RS3R hanno apprezzato
Pagina 1 / 4
Condividi: