English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 41 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author Benchy Help Przez plucht on Dec 03, 20 2677 3 plucht How to remove the buddy board? Przez TeachThePrints on Dec 01, 20 2608 4 TeachThePrint... Jagged mulitple perimeters on first layer inst... Przez Neophyl on Dec 01, 20 1878 3 mgtarallo Extruder clogging and extruding. Have to print... Przez Daniel on Nov 28, 20 1977 4 Daniel Issues Flashing Firmware with PrusaSlicer Przez willem123 on Nov 28, 20 3103 5 willem123 Mini - not sticking after unclog Przez rockytoptim on Nov 28, 20 1964 7 rcadmus Y axis going off bed in first layer calibratio... Przez Gordon W on Nov 27, 20 1555 3 CdtData 1st print: Filament seems to be stuck in the e... Przez Gordon W on Nov 27, 20 1905 5 tommytakis Filament not sticking well to other filament/s... Przez Youngatheart20... on Nov 26, 20 1943 4 Youngatheart2... Bulging corners Przez tompjagiello on Nov 26, 20 11117 24 tompjagiello Bad quality prints on brand new Prusa MINI Przez P.E.T.A.R. on Nov 25, 20 4185 5 cichy77 Quality degrading as the print goes higher Przez Youngatheart20... on Nov 22, 20 2044 8 Youngatheart2... Gaps on Top Layer Infill and Perimeter Przez herbert on Nov 19, 20 6291 3 herbert LCD Screen White Answered Przez karl-herbert on Nov 16, 20 2077 2 Inês Santos Strange stripe in the middle of prints Przez karl-herbert on Nov 15, 20 3466 14 kobazik Clicking sounds from the extruder + nozzle iss... Przez DrorFux on Nov 14, 20 2226 2 DrorFux Remaining time: peed Answered Przez karl-herbert on Nov 14, 20 4106 2 DrorFux Extruder area leaking filament Przez michael_g24 on Nov 14, 20 4798 8 michael_g24 Consistent layer bulge on whistle test print Przez karl-herbert on Nov 13, 20 2740 9 bunc Filament sensor does not stop the print Przez Izmet Fekali on Nov 13, 20 2839 3 Izmet Fekali Strona 41 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: