English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 36 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author Prusa Mini+ Bed adhesion trouble to default st... Przez cwbullet on Mar 09, 21 4999 5 aussieinkguy Not accurate printing -layers in incorrect pos... Przez Michiel Bonten... on Mar 09, 21 1731 3 Michiel Bonte... Mini Z axis have a non 90 degree via Y Przez Javacer on Mar 08, 21 2172 3 Javacer Bumps on Walls of Prints Przez Diem on Mar 08, 21 4683 4 Ya Boi Illino... Gaps in interior webbing? Is this right? Przez Javacer on Mar 08, 21 2015 2 Drummermls Textured first layer Przez The MadCadder on Mar 07, 21 1969 4 DustlessOrpha... Old age question..... first layer Przez raymate on Mar 07, 21 2280 4 raymate Mesh bed leveling failed. Answered Przez Mark Pearson on Mar 06, 21 12586 22 Bernd z-axis : even at -2.000 it's still too high :-... Przez Michiel Bonten... on Mar 06, 21 2241 5 Michiel Bonte... Twisted/inconsistent filament string Przez PrusaTester202... on Mar 05, 21 1532 1 PrusaTester20... First Prints: Underextrusion, Bad Seams Przez Hilbe on Mar 05, 21 1411 1 Hilbe Under Extrusion / Horizontal Lines Przez Youngatheart20... on Mar 05, 21 1342 1 Youngatheart2... Belt tension on Mini Przez towlerg on Mar 04, 21 3459 4 raymate Week old Mini same old problem Przez raymate on Mar 04, 21 1629 3 raymate Equally Spaced Banding Przez Collin on Mar 04, 21 1452 1 Collin Same Failure Mode in Two Different Locations Przez Collin on Mar 04, 21 1535 1 Collin Prusa Mini+ Failing Initial Testing (XYZ Axis) Answered Przez Mataos on Mar 03, 21 4378 7 Mataos First Tech Support - Not Feeling Warm and Fuzz... Przez GMoney on Mar 03, 21 1699 1 GMoney Filament flow issues Przez Katang on Mar 02, 21 2260 4 Katang Bumps / Blobs on top layer Przez codexlibris on Mar 02, 21 1808 1 codexlibris Strona 36 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: