Prusa3D Forum

Notifications

Clear all

Tango

Groupe: Enregistré

A(ont) rejoint: 2022/05/23

Reputable Member

	I have ruined satin sheets by printing PETG on them. Granted... Dans le forum How do I print this? (Printing help)	il y a 5 months
	I think @Diem is right that it was multiple issues interacti... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Got it! Considering I had one print go well until the filame... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Found the filament change and what caused it. In PrusaSlicer... Dans le forum How do I print this? (Printing help)	il y a 5 months
	It seems to be printing okay for the current print, except, ... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Here's the latest test: I stayed in the shop while I could a... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Thanks!Doing a test print now, will double-check that the no... Dans le forum How do I print this? (Printing help)	il y a 5 months
	In one word: Ugh! It's quite messy. My previous hot end was ... Dans le forum How do I print this? (Printing help)	il y a 5 months
	@Diem: Your most recent post did not show up in my browser o... Dans le forum How do I print this? (Printing help)	il y a 5 months
	I checked the X and Y axis belts. I used Prusa's online tool... Dans le forum How do I print this? (Printing help)	il y a 5 months
	I installed an MMU3 about 6 weeks ago and had an issue that ... Dans le forum How do I print this? (Printing help)	il y a 5 months
	sighIs it time to have my printer exorcised? </scarcasm... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Ran a test print. Won't be able to check it out in person fo... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Ah! I completely missed that. The only clue to that I see is... Dans le forum How do I print this? (Printing help)	il y a 5 months
	And we have failure again. Ugh!I used a glue I've used befor... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Oh, rot. I've done so many test prints that I've just realiz... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Have the photos now (sorry I couldn't include them in my ear... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Ah - now that you mention it, the times it shifted just a li... Dans le forum How do I print this? (Printing help)	il y a 5 months
	Higher Density Prints - Issues and Problems Dans le forum How do I print this? (Printing help)	il y a 5 months
	Easy and Quick Steel Sheet Offset Adjustment - Any way other... Dans le forum General discussion, announcements and releases	il y a 5 months

Page 1 / 16 Suivant

Statistiques du forum

565 Forums

64.3 K Sujets

450.1 K Messages

19 En-ligne

70.5 K Membres

Le dernier des messages: BuddyCam Notre nouveau membre: Jürgen Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé