ssill2 – Activité – Prusa3D Forum

Notifications

Clear all

ssill2

Groupe: Enregistré

A(ont) rejoint: 2021/01/18

Noble Member

	welcome to MMU printing. Thankfully with the XL there's a l... Dans le forum Hardware, firmware and software help	il y a 2 years
	you really don't want to be doing manual changes for very ma... Dans le forum General discussion, announcements and releases	il y a 2 years
	Interesting, admittedly I've not rerun the fan calibration s... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	Yeah, I like the MK4 better now that things are dialed in. ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	This 100%. Be prepared to burn some filament initially to g... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Welcome to printing tpu lol. You hopefully see now why I ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I'm not sure why you'd get the clicking on the bridging infi... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Sure, let us know how it goes. TPU is annoying until you g... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I looked at your .3mf. and since you've slowed down your r... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Not many things in 3d printing are as rewarding as finally g... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Yes, I had forgotten about that option, but I was going to m... Dans le forum How do I print this? (Printing help)	il y a 2 years
	for the sainsmart I do 3.5mvs, vs your 3.6. if you lower t... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I don't even use the spool inserts for the printdry. I just... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I don't feed the filament from the dry box. I just try the ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Are you getting filament wrapped around the extruder gear? ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Glad to help. In general stringing can be reduced by loweri... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I use the same tension for every material. You shouldn't ha... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Fair enough. you can get a lot of strength by paying with ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	you said your spool is marked as 220C as the top temp? If s... Dans le forum How do I print this? (Printing help)	il y a 2 years
	the 100% infill is really what is contributing to how long t... Dans le forum How do I print this? (Printing help)	il y a 2 years

Page 11 / 103 Précédent Suivant

Statistiques du forum

598 Forums

71.3 K Sujets

500.9 K Messages

15 En-ligne

82.3 K Membres

Le dernier des messages: Update...(Kind of) Notre nouveau membre: Jon Troiano Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé