Rainer – Actividad – Prusa3D Forum

Avisos

Vaciar todo

Rainer

Grupo: Registrado

Registrado: 2020/10/18

Honorable Member

	0.6x0.2x135=16.2mm²/s it will need a high flow nozzle. I don... En el foro Input Shaper (MK4)	hace 3 years
	Do you think the Bambulab and others have these extremely lo... En el foro Input Shaper (MK4)	hace 3 years
	Set the flow in the filament settings to 0.95 or even 0.9. M... En el foro Assembly and first prints troubleshooting	hace 3 years
	Maybe there is a reason for this change? 🙄 En el foro Input Shaper (MK4)	hace 3 years
	That's why prusa does that with the profiles. It doesn't get... En el foro Input Shaper (MK4)	hace 3 years
	Prusa are not the only ones who deliver klipper input shaper... En el foro General discussion, announcements and releases	hace 3 years
	If you compare both profiles, the speed and acceleration at ... En el foro Input Shaper (MK4)	hace 3 years
	Prusa does not use Marlin at the input Shaper. Klipper code ... En el foro General discussion, announcements and releases	hace 3 years
	With my contribution I actually meant more the thread starte... En el foro Input Shaper (MK4)	hace 3 years
	But this setting is only for support material. Not for the e... En el foro How do I print this? (Printing help)	hace 3 years
	You can print the test prints from my thread, once with your... En el foro Input Shaper (MK4)	hace 3 years
	First I would check if the screws holding the heatbreak are ... En el foro How do I print this? (Printing help)	hace 3 years
	It was the same for me and I didn't really believe it either... En el foro How do I print this? (Printing help)	hace 3 years
	Clean your sheet with Dish Cleaner to a kitchen sponge and l... En el foro How do I print this? (Printing help)	hace 3 years
	You can try to reduce the flow to 95% or even 90%. Reducing ... En el foro General discussion, announcements and releases	hace 3 years
	Actually, all speed brakes are turned off. But really it's a... En el foro Input Shaper (MK4)	hace 3 years
	After checking everything. All screws tightened on the Y axi... En el foro Assembly and first prints troubleshooting	hace 3 years
	Did you use my GCode? When I look at the speed of my Gcode i... En el foro Input Shaper (MK4)	hace 3 years
	The problem is not just the belt, but the stepper bearings a... En el foro Assembly and first prints troubleshooting	hace 3 years
	For me the test showed the following. X44.6 Y37.8 Belt tensi... En el foro Input Shaper (MK4)	hace 3 years

Página 21 / 34 Anterior Siguiente

Estadísticas del Foro

598 Foros

71.4 K Temas

501.3 K Respuestas

10 En línea

82.3 K Miembros

Último Mensaje: Less Grid Boxes on the Bed on Mini Prusa vs MK4 in Prusa Slicer 2.9.4 Nuestro miembro más reciente: Jon Troiano Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado