Rainer – Activité – Prusa3D Forum

Notifications

Clear all

Rainer

Groupe: Enregistré

A(ont) rejoint: 2020/10/18

Honorable Member

	It was the same for me and I didn't really believe it either... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Clean your sheet with Dish Cleaner to a kitchen sponge and l... Dans le forum How do I print this? (Printing help)	il y a 2 years
	You can try to reduce the flow to 95% or even 90%. Reducing ... Dans le forum General discussion, announcements and releases	il y a 2 years
	Actually, all speed brakes are turned off. But really it's a... Dans le forum Input Shaper (MK4)	il y a 2 years
	After checking everything. All screws tightened on the Y axi... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	Did you use my GCode? When I look at the speed of my Gcode i... Dans le forum Input Shaper (MK4)	il y a 2 years
	The problem is not just the belt, but the stepper bearings a... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	For me the test showed the following. X44.6 Y37.8 Belt tensi... Dans le forum Input Shaper (MK4)	il y a 2 years
	Watch from 2:45 Dans le forum Input Shaper (MK4)	il y a 2 years
	In this thread I have Gcode for measuring the resonance. Per... Dans le forum Input Shaper (MK4)	il y a 2 years
	In this thread I have Gcode for measuring the resonance. P... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	I have 2 GCode for the MK4 high with PLA and PETG. It is use... Dans le forum Input Shaper (MK4)	il y a 2 years
	Sure, but I don't really want either. There must be a reason... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	For me, the pattern corresponds to the ribs of the belt. Als... Dans le forum Assembly and first prints troubleshooting	il y a 2 years
	My frequency X 44.6 Y 37.8. Input shaper as intended by Prus... Dans le forum Input Shaper (MK4)	il y a 2 years
	You have to change the custom GCode in the printer settings.... Dans le forum Input Shaper (MK4)	il y a 2 years
	I left the original values. For the first part, I calculated... Dans le forum Input Shaper (MK4)	il y a 2 years
	I have now set the Belts to a bit to Tight. I don't want to ... Dans le forum Input Shaper (MK4)	il y a 2 years
	I'm now in the middle with the belt tension. Measured with t... Dans le forum Input Shaper (MK4)	il y a 2 years
	I printed the part again with 0.20 speed on the MK4 and Mini... Dans le forum Input Shaper (MK4)	il y a 2 years

Page 21 / 33 Précédent Suivant

Statistiques du forum

585 Forums

68.4 K Sujets

478.9 K Messages

12 En-ligne

76.4 K Membres

Le dernier des messages: The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One Notre nouveau membre: rhn Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé