Rainer – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

Rainer

Gruppe: Registriert

Beigetreten: 2020/10/18

Honorable Member

	It was the same for me and I didn't really believe it either... Im Forum How do I print this? (Printing help)	Vor 2 years
	Clean your sheet with Dish Cleaner to a kitchen sponge and l... Im Forum How do I print this? (Printing help)	Vor 2 years
	You can try to reduce the flow to 95% or even 90%. Reducing ... Im Forum General discussion, announcements and releases	Vor 2 years
	Actually, all speed brakes are turned off. But really it's a... Im Forum Input Shaper (MK4)	Vor 2 years
	After checking everything. All screws tightened on the Y axi... Im Forum Assembly and first prints troubleshooting	Vor 2 years
	Did you use my GCode? When I look at the speed of my Gcode i... Im Forum Input Shaper (MK4)	Vor 2 years
	The problem is not just the belt, but the stepper bearings a... Im Forum Assembly and first prints troubleshooting	Vor 2 years
	For me the test showed the following. X44.6 Y37.8 Belt tensi... Im Forum Input Shaper (MK4)	Vor 2 years
	Watch from 2:45 Im Forum Input Shaper (MK4)	Vor 2 years
	In this thread I have Gcode for measuring the resonance. Per... Im Forum Input Shaper (MK4)	Vor 2 years
	In this thread I have Gcode for measuring the resonance. P... Im Forum Assembly and first prints troubleshooting	Vor 2 years
	I have 2 GCode for the MK4 high with PLA and PETG. It is use... Im Forum Input Shaper (MK4)	Vor 2 years
	Sure, but I don't really want either. There must be a reason... Im Forum Assembly and first prints troubleshooting	Vor 2 years
	For me, the pattern corresponds to the ribs of the belt. Als... Im Forum Assembly and first prints troubleshooting	Vor 2 years
	My frequency X 44.6 Y 37.8. Input shaper as intended by Prus... Im Forum Input Shaper (MK4)	Vor 2 years
	You have to change the custom GCode in the printer settings.... Im Forum Input Shaper (MK4)	Vor 2 years
	I left the original values. For the first part, I calculated... Im Forum Input Shaper (MK4)	Vor 2 years
	I have now set the Belts to a bit to Tight. I don't want to ... Im Forum Input Shaper (MK4)	Vor 2 years
	I'm now in the middle with the belt tension. Measured with t... Im Forum Input Shaper (MK4)	Vor 2 years
	I printed the part again with 0.20 speed on the MK4 and Mini... Im Forum Input Shaper (MK4)	Vor 2 years

Seite 21 / 33 Vorherige Nächstes

Forums-Statistiken

585 Foren

68.4 K Themen

478.9 K Beiträge

12 Online

76.4 K Mitglieder

Letzter Beitrag: The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One Unser neuestes Mitglied: rhn Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen