PJR – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

PJR

Gruppe: Moderator

Beigetreten: 2015/06/01

Titel: Antient Member Moderator

	Hi Marten Best way to calibrate feed is to change the "flow... Im Forum Software (Archive)	Vor 10 years
	Guys I have a spare Y chassis and a few spare screws from t... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Michal OK, I use blue tape for glass levelling because I... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	OK, then download Cura, slice and print a simple model with ... Im Forum Software (Archive)	Vor 10 years
	Kristof Bulge facing down not up. Tempered glass is subjec... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Kristof Does it help if you turn the glass upside down? ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Rob Yes, that's over-extrusion of the first layer, usual... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Bruce I often tend towards overthinking problems. The s... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Scott I don't know of any other users reporting this iss... Im Forum Software (Archive)	Vor 10 years
	Sascha There is one more option that has occurred to me and... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Yeah, it would probably need to go around a 90 degree angle,... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Sascha Personally I wouldn't go above 40mm due to the space... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Nathan Best bet - either cabling or fuse. Take out the ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Kristof and Welcome to the forum. Your item 2. usually i... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Michal A 3 to 5mm brim at 70 degrees on glass should work ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	That's a 30mm fan... These small fans do run very fast and ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Michal Keep the printer away from any drafts and increas... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Sascha Which fan is this? Part fan or PSU fan? If it's... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi There Can you post screenshots of your basic and advance... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Constantine. Yes, that is also a likely cause of the shi... Im Forum Prusa i3 kit (Archive)	Vor 10 years

Seite 251 / 281 Vorherige Nächstes

Forums-Statistiken

598 Foren

70.9 K Themen

497.3 K Beiträge

16 Online

82.3 K Mitglieder

Letzter Beitrag: Update...(Kind of) Unser neuestes Mitglied: jbpr Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen