PJR – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

PJR

Gruppe: Moderator

Beigetreten: 2015/06/01

Titel: Antient Member Moderator

	Steve At the end of a print, the heaters should be turned o... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Nigel Likewise, I prefer to buy from E3D (usually at the sa... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Bill That is probably the default setting as provided by... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Steve That is not the case. There is no need to remove the... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Steve I don't know Slic3r, but most other slicers have the ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Richard Mine broke in a couple of places last week; I used ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Jozef Regarding resolution. Standard M5 has a pitch of 0.8... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Steve It is important to cable tie the spiral wrap and cabl... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Steve This is possible by inserted a line of GCode at th... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Jozef Big Ben was printed with the standard "original". ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Jake Yeah, that does happen. Higher layers will print fine... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Jake That looks like a calibration issue; bed too high a... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Christophe Unfortunately, your picture doesn't show any str... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Andy That's about right. It will be held in place with ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Jarred No problems... It really does help, but only when... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Paolo Personally I never use quiet mode. I believe that it... Im Forum Print tips (Archive)	Vor 10 years
	Hi Nigel What Jarred actually meant to say was that if you ... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Jozef My design actually looks more like my chinese clon... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Jake I find this method works best for me (from step 3):... Im Forum Prusa i3 kit (Archive)	Vor 10 years
	Hi Christophe The V6 is a simple swap-over with no adjustme... Im Forum Prusa i3 kit (Archive)	Vor 10 years

Seite 229 / 281 Vorherige Nächstes

Forums-Statistiken

598 Foren

70.9 K Themen

496.9 K Beiträge

13 Online

82.2 K Mitglieder

Letzter Beitrag: Intense layershift after Core One + Upgrade Unser neuestes Mitglied: Martin Waßmann Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen