PJR – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

PJR

Gruppe: Moderator

Beigetreten: 2015/06/01

Titel: Antient Member Moderator

	Acetone is a bit aggressive and can damage ABS parts if spil... Im Forum Others (Archive)	Vor 8 years
	Cory M140 S<BED> ; Heat the bed to print temp - ... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Cory To save a minute or two, you can heat the extruder to ... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	So my live Z is around 350. If the back left corner needs a ... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	It is released here: The only issue I have found is the "C... Im Forum Prusa i3 kit (Archive)	Vor 8 years
	Upgrade to 3.0.11-RC1 which will do it all for you at the pr... Im Forum Prusa i3 kit (Archive)	Vor 8 years
	Well, here's the thing. I do not need to use "temperature c... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	PAX Just a thought - the new "probe temp compensation" in 3... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	While were at the topic is there anything else that "needs" ... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	This is awesome PJR! i think you're about to save my sanity.... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Peter Which branch of the firmware are you using for your m... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	so your G80 starts the 9 point calibration sequence, as at e... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Print on eof the pre-sliced models from the SD card. If you... Im Forum Prusa i3 kit (Archive)	Vor 8 years
	Cory You should always include a G80 command in the start G... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Can you post a picture of the bed with the labels of each po... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	so you'll always need to feed the printer with an exclusive ... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Just a couple of things I should clarify: The "humps" and "... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Jeff I had a quick look at the G80 code section (Label: cas... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	that's quite weird. why aren't there 8 "tuning values"... J... Im Forum Assembly and first prints troubleshooting	Vor 8 years
	Unfortunately, I recently found that Bed Level Correction (e... Im Forum Assembly and first prints troubleshooting	Vor 8 years

Seite 118 / 281 Vorherige Nächstes

Forums-Statistiken

585 Foren

68.4 K Themen

479.1 K Beiträge

10 Online

76.5 K Mitglieder

Letzter Beitrag: Problems with Prusa XL since version 6.2.1 Unser neuestes Mitglied: Camster Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen