|
Looks like pixel defects. How old is your screen? Have you r... Dans le forum How do I print this? (Printing help) |
il y a 3 years |
|
Jap, you don't need to do PID tuning on the Mini at all. And... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
The Prusa Mini doesn't use Marlin PID but a combination of a... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Die Wandungszahl an den entsprechenden Stellen zu erhöhen wi... Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 3 years |
|
I'm most excited to work on or with an e3D Revo Micro printh... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
I still don't see a reason for custom firmware on the Mini. ... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
The part is scaled for an i3 build plate, but your selected ... Dans le forum Hardware, firmware and software help |
il y a 3 years |
|
@florent-duret are you sure? The Mini uses the same thermist... Dans le forum General discussion, announcements and releases |
il y a 3 years |
|
RE: PrusaSlicer 2.4 is here! Dans le forum PrusaSlicer |
il y a 3 years |
|
Hängt vermutlich mit meiner Abneigung zu 3D Jake zusammen. 😳... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 3 years |
|
Selbst schuld, wenn man bei 3D-Jake anstelle das Herstellers... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 3 years |
|
Das sind Modelle für den SLA-, nicht den FDM-Druck. Das Stüt... Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 3 years |
|
In den Einstellungen gibt es die Option nur eine Prusainstan... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 3 years |
|
RE: New e3d hot end Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
It's called Revo, not Rivo and here is the upgrade guide. Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Dafür musst du aber den G-Code verstehen und bearbeiten. Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 3 years |
|
It's just a WiFi monitor. G-Code and controller are still lo... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
There was some work on the Buddy firmware recently. So it sh... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 3 years |
|
Na PrusaSlicer. Steht doch alles in der Anleitung des Drucke... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 3 years |
|
Bin mir nicht sicher, was genau du damit meinst.gcode ist da... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 3 years |