|
Hi Karl,
I had a question about the MMU setup. When I use... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 1 month |
|
Karl, I got most of it working. Do you think I can use the M... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 4 months |
|
Karl, I got most of it working. Do you think I can use the M... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 4 months |
|
One more photo.
aedf801a-klipper_config.png Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Where I placed the files based on your document
e408f... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
I don't know what it is but I just can't get the MCU to conn... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Just discovered rollback through Kiauh. Will try that out. Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Thanks Karl. I might be wrong (I searched everywhere), but I... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Karl, do you know which Klipper version you used? It seems l... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
That helps so much!
It might just be the angle of the phot... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Hi Karl
I spent a few hours looking everything over. I also... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
I am looking over the files I received. It's very impressive... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Thank you Karl. You are awesome! Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Hi Karl,Dropbox says both files don't exist. Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
Hi Karl, can I please get the information to run the MMU wit... Dans le forum Benutzermodifikationen - OctoPrint, Gehäuse, Düsen, … |
il y a 5 months |
|
I'm agreeing with Shushuda that different pulleys made a dif... Dans le forum Hardware, firmware and software help |
il y a 7 months |
|
I agree Jurgen. Not sure if this applies to the Core but I'v... Dans le forum Hardware, firmware and software help |
il y a 7 months |
|
Toothed idler made no difference in VFAs for my mk3s+. Dans le forum Hardware, firmware and software help |
il y a 10 months |
|
I think you're speaking of the super fine vertical artifacts... Dans le forum Hardware, firmware and software help |
il y a 10 months |
|
Glitter or matte filaments hide those. Try dark petg and you... Dans le forum Hardware, firmware and software help |
il y a 10 months |
