flubber – Activité – Prusa3D Forum

Notifications

Clear all

flubber

Groupe: Enregistré

A(ont) rejoint: 2019/12/30

Eminent Member

	Bob, I was not blamestorming. I was adding the part from the... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@drewread “But I have consulted your issue with my colleague... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Just printing another test. But the first two are done. Lig... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Right. I can see the issue is on the test part. I am going t... Dans le forum How do I print this? (Printing help)	il y a 5 years
	OK. I have kicked off a 1-hour test print with the stock Pru... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro I think the X-Plus was around £740 when I was looki... Dans le forum How do I print this? (Printing help)	il y a 5 years
	And does "drop outer wall speed WAY down, disable thin wall ... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@drewread I would also question the "Expert" or "Review"/p> Dans le forum How do I print this? (Printing help)	il y a 5 years
	@tim-m30 Hi Tim. I am not quite sure what you want. I have p... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I just loaded the model in the picture above in both slicers... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Hi Bob. I only ever print on stealth and slow all my prints... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Here is an example I have just taken. Now I made some errors... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@tim-m30 I don't think grabbing a random image online is pro... Dans le forum How do I print this? (Printing help)	il y a 5 years
	The Qidi has its issues 🙂 I have printed the same parts on... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Yes sorry, it is quite a long print. I have found the smalle... Dans le forum How do I print this? (Printing help)	il y a 5 years
	A "side effect of the technology" with the Prusa? My other p... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Can you print them successfully without a step/line... Dans le forum How do I print this? (Printing help)	il y a 5 years
	And not solved. Still an issue Dans le forum How do I print this? (Printing help)	il y a 5 years
	I have been fighting these issues and had no help from Prusa... Dans le forum How do I print this? (Printing help)	il y a 5 years
	OK.... Now I am a little calmer. Latest picture without a ri... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 2 / 3 Précédent Suivant

Statistiques du forum

559 Forums

63.1 K Sujets

443.7 K Messages

23 En-ligne

68 K Membres

Le dernier des messages: MK4s Problem Z Naht "zufällig" > Materialüberschuss / Propfen am Ansatz Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé