Prusa3D Forum

Notifications

Clear all

flubber

Groupe: Enregistré

A(ont) rejoint: 2019/12/30

Eminent Member

	@sw3de Same. I abandoned PS a while back for slicer++ whic... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@omgpham That is really interesting. Have you tried this wit... Dans le forum How do I print this? (Printing help)	il y a 5 years
	That is a very nice print a nice finish to the plastic. Flip... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@omgpham That looks like a very nice setup. Have you got a p... Dans le forum How do I print this? (Printing help)	il y a 5 years
	I am going to set my Extrusion Width's to 0 and do another p... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro "The shape itself is interesting with the varying t... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Well a doh moment from me. Checked the size in Fusion - sli... Dans le forum How do I print this? (Printing help)	il y a 5 years
	🙂 I will try mine and see if this causes the issue. I will... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro I can print it off now if you can hold on for 1 hou... Dans le forum How do I print this? (Printing help)	il y a 5 years
	What about something like 1-hour 43 mins? No flat wall thou... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Here is the pot base from one of the photos showing... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro I have not tried changing the fill angle. Dans le forum How do I print this? (Printing help)	il y a 5 years
	For me, the bulging line goes all the way around but I mostl... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Are those two ledges at slightly different heights?... Dans le forum How do I print this? (Printing help)	il y a 5 years
	Well let try and see if we can get a working functioning pri... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro This is kind of what I had in mind. No supports nee... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Kind of. Let me draw a picture Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Can you add a lip section a few mm from the top lik... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro I have been using a 70mm x 10mm shelled to 5mm as a... Dans le forum How do I print this? (Printing help)	il y a 5 years
	@bobstro Let me know when you have an STL happy to standardi... Dans le forum How do I print this? (Printing help)	il y a 5 years

Page 1 / 3 Suivant

Statistiques du forum

559 Forums

63.1 K Sujets

443.7 K Messages

21 En-ligne

68 K Membres

Le dernier des messages: MK4s Problem Z Naht "zufällig" > Materialüberschuss / Propfen am Ansatz Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé