Diem – Aktivität – Prusa3D Forum

Benachrichtigungen

Alles löschen

Diem

Gruppe: Registriert

Beigetreten: 2017/12/27

Illustrious Member

	Your first layer Z offset is a fraction too low. The print s... Im Forum How do I print this? (Printing help)	Vor 3 years
	, mentioned in Issue 1. If you mean the e3d h/e in your lin... Im Forum How do I print this? (Printing help)	Vor 3 years
	How old is your nozzle? Have you been printing abrasive fil... Im Forum General discussion, announcements and releases	Vor 3 years
	The most likely cause is a loose connection - pull and resea... Im Forum Hardware, firmware and software help	Vor 3 years
	You didn't mention changing the hotend ... you might need to... Im Forum How do I print this? (Printing help)	Vor 3 years
	Reset to defaults. Cheerio, Im Forum How do I print this? (Printing help)	Vor 3 years
	Go lower until the top starts to ripple then back off until ... Im Forum Assembly and first prints troubleshooting	Vor 3 years
	You will probably do better with 0.2mm layers as you have no... Im Forum How do I print this? (Printing help)	Vor 3 years
	There is no fixed value, it accommodates several build and u... Im Forum How do I print this? (Printing help)	Vor 3 years
	You do. It's all in the text of the article - but don't use... Im Forum How do I print this? (Printing help)	Vor 3 years
	Pull and reinsert all the plugs at the Einsy end in case you... Im Forum Hardware, firmware and software help	Vor 3 years
	Please show us your current first layer Z calibration *on th... Im Forum Assembly and first prints troubleshooting	Vor 3 years
	There is a good chance you have snapped off the tip of the f... Im Forum Hardware, firmware and software help	Vor 3 years
	Definitely not. See section 2.6.9 of:/p> This shows the prof... Im Forum How do I print this? (Printing help)	Vor 3 years
	Why 0.1mm layers? Cheerio, Im Forum How do I print this? (Printing help)	Vor 3 years
	Check your fans, particularly the print fan. Make sure they... Im Forum How do I print this? (Printing help)	Vor 3 years
	Your print sheet needs a serious clean and the Z calibration... Im Forum How do I print this? (Printing help)	Vor 3 years
	It looks like you have first layer Z calibration issues. Th... Im Forum How do I print this? (Printing help)	Vor 3 years
	Your first layer Z calibration is too low. You have a first ... Im Forum Assembly and first prints troubleshooting	Vor 3 years
	Open the idler and watch as you feed in the filament manuall... Im Forum How do I print this? (Printing help)	Vor 3 years

Seite 184 / 355 Vorherige Nächstes

Forums-Statistiken

585 Foren

68.2 K Themen

477.7 K Beiträge

10 Online

75.9 K Mitglieder

Letzter Beitrag: The Cryogrip Pro Glacier plate is an excellent cheaper alternative to the Satin plate with one minor caveat on the Core One Unser neuestes Mitglied: mnentwig Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen