cwbullet – Activité – Prusa3D Forum

Notifications

Clear all

cwbullet

Groupe: PrusaLink-beta

A(ont) rejoint: 2018/07/13

Titre: Membre

	I made a model that 2 layers think in Tinkercad using your d... Dans le forum How do I print this? (Printing help)	il y a 4 years
	I could not find anything online and it does not appear in t... Dans le forum Hardware, firmware and software help	il y a 4 years
	@nett_flanders Loosen the screw and slightly lower your SPIN... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@eng-shaimaa-elsersy That is success in my book! 😀 Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@idontwantapublicusername Then the problem solves in my book... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@coreyfro Thanks for contributing! Each entry adds to the ... Dans le forum PrusaSlicer	il y a 4 years
	Mine are not that loud. I did lubricate the rods and bearin... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@marsh Can you clarify the certificate file? What is that? Dans le forum User mods - OctoPrint, enclosures, nozzles, ...	il y a 4 years
	I mistyped. I think you are printing the same one I printed... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Success. I am going to try again. I think I forgot to cle... Dans le forum How do I print this? (Printing help)	il y a 4 years
	It took 18 minutes. Pretty good quality. I would prefer 2 ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@tim-2 That is probably the best option because you can remo... Dans le forum Hardware, firmware and software help	il y a 4 years
	@baklin I concur. Adhesion problems. @Bucens Recommend yo... Dans le forum General discussion, announcements and releases	il y a 4 years
	@vita-3 Are you sure that grub screw is not causing it? Eit... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@diem Thank you. I have owned one for 10 years and never zi... Dans le forum General discussion, announcements and releases	il y a 4 years
	I got it to slice and now I am printing. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@ringarn67 I will try. The 3mf file would not slice. I wil... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@diem Are you sure that grub screw is not causing it? Eithe... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	@sink That makes sense. Thanks. I am going to take a coupl... Dans le forum Assembly and first prints troubleshooting	il y a 4 years
	That is quite a conundrum and hard to get past. I guess thi... Dans le forum PrusaSlicer	il y a 4 years

Page 211 / 571 Précédent Suivant

Statistiques du forum

585 Forums

68.2 K Sujets

477.9 K Messages

10 En-ligne

75.9 K Membres

Le dernier des messages: Side Filament Sensor Issue Notre nouveau membre: ArtiVIVO Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé