chrischin – Activité – Prusa3D Forum

Notifications

Clear all

chrischin

Groupe: Enregistré

A(ont) rejoint: 2018/12/15

Trusted Member

	@bobstro In the before gcode I turned down the "M221 S95" co... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro Filament is Prusament PLA. Top layers with a 0.4mm ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro The red circles are rough, raised extrusions which ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro The top layer issue seems to be happening at either... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro Can you send this STL and I'll print to compare? I ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro The thinnest first layer with a smooth surface that... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki Should be ok if it's in a box lol Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki The only filament I've found so far that prints dead... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki Found his page earlier this morning and started read... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki @bostro Regarding speeds CNC Kitchen agrees! I've be... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki Wow. Very nice. It's hard to tell from those angles ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki The 0.6mm nozzle is a game-changer for larger, less ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@chocki Thanks for the info. Those speeds are half of mine. ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro I'm getting exactly 0.7mm on all four walls Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro Thanks. Looking forward to your findings. Dans le forum How do I print this? (Printing help)	il y a 6 years
	@bobstro Using Prusa default profile and I'm referring to th... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Before experimenting with the "First layer" extrusion width ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	First layer height 0.6mm nozzle Dans le forum How do I print this? (Printing help)	il y a 6 years
	@vintagepc Thanks so much. I'm going to tackles these things... Dans le forum How do I print this? (Printing help)	il y a 6 years
	gcode attached Attachment removed Dans le forum How do I print this? (Printing help)	il y a 6 years

Page 2 / 3 Précédent Suivant

Statistiques du forum

585 Forums

68.1 K Sujets

477 K Messages

11 En-ligne

75.8 K Membres

Le dernier des messages: Prusaslicer 2.9.3 September 12 release on Linux Notre nouveau membre: Tommy Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé