Bruce Labitt – Activité

Notifications

Clear all

Bruce Labitt

Groupe: Enregistré

A(ont) rejoint: 2023/03/12

Estimable Member

	I've spent far, far more than 17 hours on this issue! It's ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Thanks, @ssill2 that is very helpful. I have backed off the... Dans le forum How do I print this? (Printing help)	il y a 2 years
	It's not so obvious to me. The views are entirely different... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Here's a screenshot snippet where the Sainsoft TPU jammed. ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I will post a section later in the day. I tried my Overture... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Another filament jam. 😥 Can't seem to catch a break on this... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Beginning to see a pattern here... Good prints with dry fil... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Yes, it is satin. Thing is, just before printing I had clea... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Do you know of a less expensive solution that gets that hot?... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Not much to see. Can't see anything obvious with a photo. ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Part bowed off the sheet. There goes another attempt. Kill... Dans le forum How do I print this? (Printing help)	il y a 2 years
	216C printed a little worse than 218C. Think I will stay wi... Dans le forum How do I print this? (Printing help)	il y a 2 years
	My MK3S+ had better looking aligned seams than the MK4 using... Dans le forum How do I print this? (Printing help)	il y a 2 years
	So like Retraction length = 1mm, rather than 1.5mm? Or 1.25... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Quality, (not IS) no change in MVS(5mm3/s), retraction=20mm/... Dans le forum How do I print this? (Printing help)	il y a 2 years
	No gallery was attached. Jeepers. How convoluted. Dans le forum How do I print this? (Printing help)	il y a 2 years
	One more try on the pictures... Trying a gallery. Why do th... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Don't like to sound like a Luddite, but how do you attach pi... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I've only asked for cost on some of the things I've done for... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Thanks for going through the effort of doing this! It is gr... Dans le forum How do I print this? (Printing help)	il y a 2 years

Page 6 / 9 Précédent Suivant

Statistiques du forum

595 Forums

70.2 K Sujets

491 K Messages

13 En-ligne

81.2 K Membres

Le dernier des messages: Rough cubic infill problem Notre nouveau membre: maxluzi Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé