Bruce Labitt – Activité

Notifications

Clear all

Bruce Labitt

Groupe: Enregistré

A(ont) rejoint: 2023/03/12

Estimable Member

	Not much to see. Can't see anything obvious with a photo. ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Part bowed off the sheet. There goes another attempt. Kill... Dans le forum How do I print this? (Printing help)	il y a 2 years
	216C printed a little worse than 218C. Think I will stay wi... Dans le forum How do I print this? (Printing help)	il y a 2 years
	My MK3S+ had better looking aligned seams than the MK4 using... Dans le forum How do I print this? (Printing help)	il y a 2 years
	So like Retraction length = 1mm, rather than 1.5mm? Or 1.25... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Quality, (not IS) no change in MVS(5mm3/s), retraction=20mm/... Dans le forum How do I print this? (Printing help)	il y a 2 years
	No gallery was attached. Jeepers. How convoluted. Dans le forum How do I print this? (Printing help)	il y a 2 years
	One more try on the pictures... Trying a gallery. Why do th... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Don't like to sound like a Luddite, but how do you attach pi... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I've only asked for cost on some of the things I've done for... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Thanks for going through the effort of doing this! It is gr... Dans le forum How do I print this? (Printing help)	il y a 2 years
	No enclosure yet. So printed out in the open. It was befor... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Sawed the nonIS one in half, nothing out of the ordinary (as... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Edit time expired: that wasn't long! Part dimensions. non I... Dans le forum How do I print this? (Printing help)	il y a 2 years
	@ssill2 Printing the test model with and without IS is total... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I think 3d printing in general is slow, but that's me. The ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Just noticed that, now that you pointed it out. I just resl... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Guess I need to try again. I don't see the 3mf file, let me... Dans le forum How do I print this? (Printing help)	il y a 2 years
	Giving this a try. Might take a few attempts. Here is the ... Dans le forum How do I print this? (Printing help)	il y a 2 years
	I have created a quick stl file, haven't even imported it to... Dans le forum How do I print this? (Printing help)	il y a 2 years

Page 4 / 7 Précédent Suivant

Statistiques du forum

595 Forums

69.3 K Sujets

485.3 K Messages

13 En-ligne

78.8 K Membres

Le dernier des messages: Nice print until it fails, at a loss on how to procede. Notre nouveau membre: Polysulfide Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé