Bruce Labitt – Activité

Notifications

Clear all

Bruce Labitt

Groupe: Enregistré

A(ont) rejoint: 2023/03/12

Estimable Member

	It's not so obvious to me. The views are entirely different... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Here's a screenshot snippet where the Sainsoft TPU jammed. ... Dans le forum How do I print this? (Printing help)	il y a 9 months
	I will post a section later in the day. I tried my Overture... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Another filament jam. 😥 Can't seem to catch a break on this... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Beginning to see a pattern here... Good prints with dry fil... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Yes, it is satin. Thing is, just before printing I had clea... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Do you know of a less expensive solution that gets that hot?... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Not much to see. Can't see anything obvious with a photo. ... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Part bowed off the sheet. There goes another attempt. Kill... Dans le forum How do I print this? (Printing help)	il y a 9 months
	216C printed a little worse than 218C. Think I will stay wi... Dans le forum How do I print this? (Printing help)	il y a 9 months
	My MK3S+ had better looking aligned seams than the MK4 using... Dans le forum How do I print this? (Printing help)	il y a 9 months
	So like Retraction length = 1mm, rather than 1.5mm? Or 1.25... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Quality, (not IS) no change in MVS(5mm3/s), retraction=20mm/... Dans le forum How do I print this? (Printing help)	il y a 9 months
	No gallery was attached. Jeepers. How convoluted. Dans le forum How do I print this? (Printing help)	il y a 9 months
	One more try on the pictures... Trying a gallery. Why do th... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Don't like to sound like a Luddite, but how do you attach pi... Dans le forum How do I print this? (Printing help)	il y a 9 months
	I've only asked for cost on some of the things I've done for... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Thanks for going through the effort of doing this! It is gr... Dans le forum How do I print this? (Printing help)	il y a 9 months
	No enclosure yet. So printed out in the open. It was befor... Dans le forum How do I print this? (Printing help)	il y a 9 months
	Sawed the nonIS one in half, nothing out of the ordinary (as... Dans le forum How do I print this? (Printing help)	il y a 9 months

Page 3 / 6 Précédent Suivant

Statistiques du forum

559 Forums

63.1 K Sujets

443.9 K Messages

22 En-ligne

68.1 K Membres

Le dernier des messages: Prusament PETG Matte Black Notre nouveau membre: etiennep Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé