Bruce Labitt – Actividad

Avisos

Vaciar todo

Bruce Labitt

Grupo: Registrado

Registrado: 2023/03/12

Estimable Member

	It's not so obvious to me. The views are entirely different... En el foro How do I print this? (Printing help)	hace 9 months
	Here's a screenshot snippet where the Sainsoft TPU jammed. ... En el foro How do I print this? (Printing help)	hace 9 months
	I will post a section later in the day. I tried my Overture... En el foro How do I print this? (Printing help)	hace 9 months
	Another filament jam. 😥 Can't seem to catch a break on this... En el foro How do I print this? (Printing help)	hace 9 months
	Beginning to see a pattern here... Good prints with dry fil... En el foro How do I print this? (Printing help)	hace 9 months
	Yes, it is satin. Thing is, just before printing I had clea... En el foro How do I print this? (Printing help)	hace 9 months
	Do you know of a less expensive solution that gets that hot?... En el foro How do I print this? (Printing help)	hace 9 months
	Not much to see. Can't see anything obvious with a photo. ... En el foro How do I print this? (Printing help)	hace 9 months
	Part bowed off the sheet. There goes another attempt. Kill... En el foro How do I print this? (Printing help)	hace 9 months
	216C printed a little worse than 218C. Think I will stay wi... En el foro How do I print this? (Printing help)	hace 9 months
	My MK3S+ had better looking aligned seams than the MK4 using... En el foro How do I print this? (Printing help)	hace 9 months
	So like Retraction length = 1mm, rather than 1.5mm? Or 1.25... En el foro How do I print this? (Printing help)	hace 9 months
	Quality, (not IS) no change in MVS(5mm3/s), retraction=20mm/... En el foro How do I print this? (Printing help)	hace 9 months
	No gallery was attached. Jeepers. How convoluted. En el foro How do I print this? (Printing help)	hace 9 months
	One more try on the pictures... Trying a gallery. Why do th... En el foro How do I print this? (Printing help)	hace 9 months
	Don't like to sound like a Luddite, but how do you attach pi... En el foro How do I print this? (Printing help)	hace 9 months
	I've only asked for cost on some of the things I've done for... En el foro How do I print this? (Printing help)	hace 9 months
	Thanks for going through the effort of doing this! It is gr... En el foro How do I print this? (Printing help)	hace 9 months
	No enclosure yet. So printed out in the open. It was befor... En el foro How do I print this? (Printing help)	hace 9 months
	Sawed the nonIS one in half, nothing out of the ordinary (as... En el foro How do I print this? (Printing help)	hace 9 months

Página 3 / 6 Anterior Siguiente

Estadísticas del Foro

559 Foros

63.1 K Temas

443.8 K Respuestas

22 En línea

68.1 K Miembros

Último Mensaje: prusaslicer 2.9.0 alpha1 - how to use scarf seam Nuestro miembro más reciente: etiennep Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado