Prusa3D Forum

Notifications

Clear all

Aureum Locus

Groupe: Enregistré

A(ont) rejoint: 2018/11/06

Trusted Member

	@thomas-f17 Thanks for the advice. I have a Prusa Lack encl... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@deneteus Good point about the uneven drying. That’s a good ... Dans le forum General discussion, announcements and releases	il y a 4 years
	@jmone Thanks for all of that. I too like the ePA-CF but I ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone OK. That's affordable and justifiable. Do you mind ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone That looks like a great idea, but he price is a bit o... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone Yep, It must have been pretty wet. The eSun bags are... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Here's an image of the final print. The one on the right is... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone Ultra Dry seems the only sensible way to go. I'll ad... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Average humidity here (Canberra) ranges from 35% to 64% so n... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone Cool. I'm in Oz too. Thanks for that. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone this cabinets look amazing. What are they and where ... Dans le forum How do I print this? (Printing help)	il y a 4 years
	One hour in, still showing banding. Looks like I might nee... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone That’s a great looking setup. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone That’s good to know. Thanks. Dans le forum How do I print this? (Printing help)	il y a 4 years
	@jmone Thanks. I agree with you. It’ll be interesting to see... Dans le forum How do I print this? (Printing help)	il y a 4 years
	Oh, and no stringing or warping observed. I did have a 20mm... Dans le forum How do I print this? (Printing help)	il y a 4 years
	OK, That's very interesting. I just got a commission from a... Dans le forum How do I print this? (Printing help)	il y a 4 years
	@guy-k2 Great work! Thanks. Looks like I’m off to Costco to ... Dans le forum General discussion, announcements and releases	il y a 5 years
	@jmone I agree. A bit of drying seems to fix stringiness on ... Dans le forum General discussion, announcements and releases	il y a 5 years
	@jmone Thanks for that. I printed the Prusa R5 hot end cover... Dans le forum General discussion, announcements and releases	il y a 5 years

Page 1 / 3 Suivant

Statistiques du forum

535 Forums

59.7 K Sujets

427.6 K Messages

16 En-ligne

64.1 K Membres

Le dernier des messages: 0.3mm layer height no longer available ? Notre nouveau membre: LandonC Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé