Recent Posts

Forums | Topics

Page 1 / 37 Next

	Topic Title	Forum
	Noticing Prusa high temp filament spools tend to come apart after removing from the dryer By hyiger 3 hours ago \| Last Post: 3 hours ago	General discussion, announcements and releases
	So I've now had 2 instances where the plastic end ... 3 hours ago By hyige...
	Strange issues on prints By vsions 6 hours ago \| Last Post: 4 hours ago	Assembly and first prints troubleshooting
	It's a combination of extreme overhang and the dir... 4 hours ago By Diem Hello, I have been trying to figure out why my pri... 6 hours ago By vsion...
	Chronic Under-Extrusion - Core ONE By PaltrySun 22 hours ago \| Last Post: 4 hours ago	General discussion, announcements and releases
	Once you have consistently dry filament (and possi... 4 hours ago By Diem Thanks for the responses! I only used PLA and P... 6 hours ago By Paltr... clicking/grinding filament and stringy filament Ag... 7 hours ago By Diem view all posts
	PrusaConnect keeps showing OFFLINE and other connection issues By Roger 6 months ago \| Last Post: 4 hours ago	Bugs & Errors
	Same here, when starting up everything shows ok, a... 4 hours ago By sabre... I've been having the same issues with my Core One.... 2 weeks ago By Hammy I'm still getting these Offline statuses, been hap... 3 weeks ago By Chris view all posts
	Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 4 weeks ago \| Last Post: 5 hours ago	General discussion, announcements and releases
	I am having the same issue! Hope there's an answer... 5 hours ago By Crise... That is correct. Any suggestions? 2 weeks ago By Dik H... Buddy Camera that’s linked to a Core device (maybe... 2 weeks ago By Deepa...
	Large ABS + PLA print, PLA keeps clogging By xatlas0 2 weeks ago \| Last Post: 6 hours ago	General discussion, announcements and releases
	I experienced a similar issue with the combo of AS... 6 hours ago By dawso... What's the best way to check size and roundness so... 2 weeks ago By Diem The three most likely causes: - Out of spec filame... 2 weeks ago By xatla... view all posts
	Core One skipping steps/Layer shift By Enrique Specht 6 months ago \| Last Post: 7 hours ago	Hardware, firmware and software help
	I am having the exact same problem. The location o... 7 hours ago By Jane ... I seem to have the same, or at least similar probl... 6 days ago By Marti... I am experiencing the same issue, with a printable... 7 days ago By wdvc view all posts
	VFA still there after all "fixes" By Kenneth Li 7 hours ago \| Last Post: 7 hours ago	Hardware, firmware and software help
	Even after tensioning belts (i overtensioned both ... 7 hours ago By Kenne...
	filament dryer By skylab9999 2 days ago \| Last Post: 7 hours ago	General discussion, announcements and releases
	Desiccant type dryers (like silica gel units): The... 7 hours ago By skyla... I still have a question, where does the moisture g... 8 hours ago By Green... The lamp in the overhead box is a led corn roll ty... 1 day ago By skyla... view all posts
	Two head printing - Automatic switch By AAM Metaldyne 16 hours ago \| Last Post: 7 hours ago	How do I print this? (Printing help)
	You are looking for the Spooljoin function: Cheer... 7 hours ago By Diem Hello, My compagny order a printer XL for indust... 16 hours ago By AAM M...
	Core one firmware 6.4.0 alpha By Philippe BAUER 7 hours ago \| Last Post: 7 hours ago	Hardware, firmware and software help
	For the core one, concerning the phase stepping c... 7 hours ago By Phili...
	Düsentemperatur wird nicht angezeigt By [email protected] 13 hours ago \| Last Post: 7 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Heizt er den auf? Nicht, daß der Sensor in Ordnung... 7 hours ago By Digib... Hallo zusammen, ich habe heute meinen MK4, mehr od... 13 hours ago By diete...
	Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App By Vincent5840 5 months ago \| Last Post: 8 hours ago	Hardware, firmware and software help
	That's not entirely right. It may level the bed at... 8 hours ago By CJD Thank you! 🙂 18 hours ago By Timma... RE: Belt Tension Issues on New Core One – Layer Shifting & Unreliable Tuner App 19 hours ago By Raine... view all posts
	MK4 Prusa Enclosure By Mullu 1 day ago \| Last Post: 8 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	danke für die schnelle Antwort. Ich bevorzuge die ... 8 hours ago By Mullu Entweder den PTFE-Schlauch durch drücken von oben ... 1 day ago By Walte... Hallo, ich habe dieses Wochenende das Gehäuse für ... 1 day ago By Mullu
	Close to losing my mind By J 2 days ago \| Last Post: 8 hours ago	Assembly and first prints troubleshooting
	If you use manual controls does the print head mov... 8 hours ago By CJD Somehow, yes it does 1 day ago By J Can’t help but feel these’re something fundamental... 1 day ago By gb160 view all posts
	XL firmware 6.4.0 alpha By Philippe BAUER 8 hours ago \| Last Post: 8 hours ago	Hardware, firmware and software help
	The alpha 6.4.0 firmware causes big head crash. Al... 8 hours ago By Phili...
	Nozzle temperature not correct By [email protected] 13 hours ago \| Last Post: 8 hours ago	Assembly and first prints troubleshooting
	It's possible the thermistor in the heat block is ... 8 hours ago By hyige... No firsthand knowledge but the very first (maybe s... 9 hours ago By Steve Hello everyone, I more or less successfully conver... 13 hours ago By diete...
	CORE One: Funktion Türschalter? By M3T 5 days ago \| Last Post: 8 hours ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Nach Kontakt mit Prusa des Rätsels Lösung: 1. Der ... 8 hours ago By M3T Hallo, nach Inbetriebnahme des CORE One (Kalibrier... 5 days ago By M3T
	Strange issues on prints By vsions 9 hours ago \| Last Post: 9 hours ago	How do I print this? (Printing help)
	Hello, I have been trying to figure out why my pri... 9 hours ago By vsion...