| |
Topic Title |
Forum |
 |
Where is the upgraded bed for Core One ? By Print_Fandango 3 weeks ago | Last Post: 7 days ago
|
General discussion, announcements and releases |
| |
|
 |
Possible bug or error in Gcode ? (Layer shift) By Wuhan 2 weeks ago | Last Post: 7 days ago
|
General discussion, announcements and releases |
| |
|
 |
Core One - Z osa By Killer85-Z 3 months ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Core One - tisk více filamenty By Kukačka 4 months ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Core One - postřehy By Jedle2000 7 months ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
Why is this happening i took everything and cleaned and still getting the same thing By Wince77 7 days ago | Last Post: 7 days ago
|
Hardware, firmware and software help |
| |
|
 |
rattling during printing By Bezbolestný Pekáč 3 weeks ago | Last Post: 7 days ago
|
Prusa CORE One L |
| |
|
 |
prestane dávať filament By Jamal 1 week ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
 |
CORE ONE/ + / L By Jardoslav 1 month ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
Problém s osou Y By Skyro 4 weeks ago | Last Post: 7 days ago
|
Obecná diskuze, oznámení a novinky |
| |
|
|
|
TPU issues, sorry if its been asked before! By SHeath 7 days ago | Last Post: 7 days ago
|
How do I print this? (Printing help) |
| |
|
 |
Core One +: Auto Vent opening By Andhrimnir 2 weeks ago | Last Post: 7 days ago
|
General discussion, announcements and releases |
| |
|
 |
First layer resolution different from second layer when should be equal. By rmayol 1 week ago | Last Post: 7 days ago
|
How do I print this? (Printing help) |
| |
|
 |
How does Prusa Connect Queue work? By Phil 1 week ago | Last Post: 1 week ago
|
General discussion & User Experience & Ideas |
| |
|
|
|
Hot end settings cool down/heat up... By cboshdave 1 week ago | Last Post: 1 week ago
|
Hardware, firmware and software help |
| |
|
 |
Extruder fördert kein Filament mehr, gibt knackende Geräusche von sich By Belchengeist 7 months ago | Last Post: 1 week ago
|
Hilfe zur Hardware, Firmware und Software |
| |
|
|
|
XL 2 tetes, problème 1ere couche By Erwan QUELLET 2 weeks ago | Last Post: 1 week ago
|
Dépannage pour l'assemblage et les premières impressions |
| |
|
 |
Change layer direction in Slicer/Gcode - clockwise 1st then next layer counter-clockwise By Rincewind 1 week ago | Last Post: 1 week ago
|
PrusaSlicer |
| |
|
|
|
The first purge before to print with mmu3 By rmayol 1 week ago | Last Post: 1 week ago
|
How do I print this? (Printing help) |
| |
|
 |
Accelerometer reduced noise during printing By docsascha 2 weeks ago | Last Post: 1 week ago
|
General discussion, announcements and releases |
| |
|