| |
Topic Title |
Forum |
 |
Print Bed Loose? By Shorty54 8 hours ago | Last Post: 8 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Poor Print Quality on Sloped Surfaces That Face the Rear By t5montecarlo 2 weeks ago | Last Post: 9 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Direct addressing of GPIO board By Denesius 4 days ago | Last Post: 9 hours ago
|
Prusa add-ons (GPIO, accelerometer,...) |
| |
|
 |
MK4S ironing settings different than MK4? By coalesce714 13 hours ago | Last Post: 9 hours ago
|
How do I print this? (Printing help) |
| |
|
 |
Prusa MK3S+ not opening RPi Port By ETTItroff 9 hours ago | Last Post: 9 hours ago
|
Prusa Connect & PrusaLink |
| |
|
 |
first layer anomaly By simoneg 2 days ago | Last Post: 11 hours ago
|
Hardware, firmware and software help |
| |
|
 |
Under extrusion? at start of seam By Matt 2 weeks ago | Last Post: 11 hours ago
|
Hardware, firmware and software help |
| |
|
|
|
Heatsink spacer missing, how to move forward? By Shasha 1 year ago | Last Post: 12 hours ago
|
Assembly and first prints troubleshooting |
| |
|
 |
Core One screams. Don't know why. By JPMath 3 days ago | Last Post: 13 hours ago
|
Hardware, firmware and software help |
| |
|
|
|
Failed First Print - Fix for PETG Benchy that shifted after a couple layers on textured sheet? By Stormy 2 weeks ago | Last Post: 13 hours ago
|
Prints troubleshooting |
| |
|
|
|
partial clog cold pulls not working--is there a current knowledgebase page for this? By Christopher Hickie 3 days ago | Last Post: 13 hours ago
|
Hardware, firmware and software help |
| |
|
 |
PS 2.9.4 adding variable width lines to first three layers of vase mode By Jordan 1 day ago | Last Post: 13 hours ago
|
PrusaSlicer |
| |
|
 |
i3 Origional firmware upgrade failed By john.w 18 hours ago | Last Post: 14 hours ago
|
Hardware, firmware and software help |
| |
|
 |
NEMA-17 Stepper Motor High Speed Issue By Sigrid 3 days ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Prusa Connect horribly slow By gb160 3 days ago | Last Post: 14 hours ago
|
Prusa Connect & PrusaLink |
| |
|
|
|
Roadmap for Core One L By chandler 17 hours ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
"Export to G-Code" rather than "Send to Connect" ? By Nodak7 16 hours ago | Last Post: 14 hours ago
|
General discussion, announcements and releases |
| |
|
 |
Custom brim/tabs elephant's foot compensation... By 4Thee 6 days ago | Last Post: 14 hours ago
|
PrusaSlicer |
| |
|
 |
MK4S asks me to unload and load filament before the printing starts By Marteinn - 3DP Iceland 15 hours ago | Last Post: 14 hours ago
|
Hardware, firmware and software help |
| |
|
 |
As of 6.4.0, the XL still crashes toolheads into one another. It is inexcusable. By ktastrophe 1 week ago | Last Post: 16 hours ago
|
General discussion, announcements and releases |
| |
|