Recent Posts

Forums | Topics

Page 29 / 33 Prev Next

	Topic Title	Forum
	Printer printing wrong g code file By GordonMcD 12 months ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	I also have this issue. It seems to occur when the... 4 weeks ago By Johan... Yeah same issue here with my MK3S+ with firmware 3... 2 months ago By Beaco... I als0 have been having this problem...picking th... 3 months ago By Sally... view all posts
	neue Düsen passen nicht ohne Nachbearbeitung By Wolverine0815 4 weeks ago \| Last Post: 4 weeks ago	Zusammenbau und Fehlersuche bei den ersten Druckversuchen
	Habe ich in dieser Größe noch nie gesehen. 4 weeks ago By Wolve... Wer Erfahrung hat mit der Mertallbearbeitung, kann... 4 weeks ago By Frick... Hallo zusammen,ich habe bei meinem MK4 bzw. jetzt ... 4 weeks ago By Wolve...
	Pin Holes By Bryan Powell 4 weeks ago \| Last Post: 4 weeks ago	How do I print this? (Printing help)
	Thank you for your reply Tim. The test part is 3 l... 4 weeks ago By Bryan... You didn't say how many layers are involved. But i... 4 weeks ago By Tim Hello, I am attempting to print a lightbox for a b... 4 weeks ago By Bryan...
	Better anti vibration feet alternative? By perky890 4 weeks ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	I had one of the original Core Ones and it came wi... 4 weeks ago By vhubb... +1. I used them on all my Core Ones. Work great 4 weeks ago By FoxRu... You can peel off the adhesive tape and glue them o... 4 weeks ago By hyige...
	MMU3 filament load failure By William Westbo 4 weeks ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	I have a MK4 that I upgraded to a MK4S and then I ... 4 weeks ago By Willi...
	Replacing hot end. 2 wires that I can't figure where they were. By GXS 2 months ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	I've never seen wire like that on a Prusa. Perhap... 4 weeks ago By Tim which version of printer?i know on my mk3 there sh... 4 weeks ago By Sumta I had a failed ABS print that left the hot end enc... 2 months ago By GXS
	Are there any apps for testing g-code on a Core One By hyiger 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	FWIW, Octoprint on an rpi auto-selects 115200, Coo... 4 weeks ago By ssmit... Not trying to do anything other than understand wh... 4 weeks ago By hyige... Simply connect 15200,8,N,1 and sent send. Not sure... 4 weeks ago By Tim view all posts
	PrusaSlicer 2.9.3 Final is out By Petr Kubiš 4 weeks ago \| Last Post: 4 weeks ago	PrusaSlicer
	Tried to delete previous post, but update for fix.... 4 weeks ago By Danie... Well, this is awkward. Updated to this version and... 4 weeks ago By Danie... We released the final version of 2.9.3 last week! ... 4 weeks ago By Petr ...
	Unable to control printer with PRUSA App By mmmachnik 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	I recently added a MMU3 to my Core ONE and now the... 4 weeks ago By mmmac...
	Camera jammed the print board By Justin Craigie 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Wanted to add here that the Buddy camera magnets s... 4 weeks ago By hyige... Try a control/calibration/z-alignment? 4 weeks ago By ssmit... The buddy camera fell during a print and caused th... 4 weeks ago By Justi...
	MKS4 with mmu3 printed now will not By tweiner 4 weeks ago \| Last Post: 4 weeks ago	Assembly and first prints troubleshooting
	I have a MK4S with mmu3. I ordered assembled. Un... 4 weeks ago By twein...
	Looking for profiles for 3DXTech filaments By Steve 4 weeks ago \| Last Post: 4 weeks ago	PrusaSlicer
	Does anyone know where I can find PrusaSlicer prof... 4 weeks ago By Steve
	MMU Nextruder mod tension screws By Alienbliep 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	No scraping at all. I tightened the screws a littl... 4 weeks ago By James... Does your screws scrape the holes? I suggest tight... 4 weeks ago By Alien... I have the same problem. Did a few prints without ... 4 weeks ago By James... view all posts
	Print head strangely shifted right By YigalB 4 weeks ago \| Last Post: 4 weeks ago	General discussion, announcements and releases
	While printing this known duck, the head started p... 4 weeks ago By Yigal...
	What is causing this and how to deal with it. By TheBelcherMan 1 month ago \| Last Post: 4 weeks ago	How do I print this? (Printing help)
	Look at this model I got my inspiration from. Is ... 4 weeks ago By TheBe... Inside the program, I think the seam is intentiona... 4 weeks ago By Tim If you pull this little test into the slicer, bone... 4 weeks ago By TheBe... view all posts
	PrusaSlicer refuses to use shrinkage compensation By siaulip 4 weeks ago \| Last Post: 4 weeks ago	PrusaSlicer
	Upon having calibrated my 2 filaments (prusament P... 4 weeks ago By siaul...
	Advice or Suggestions on repair By phi161803 1 month ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	It might be that the belt is rubbing against the b... 4 weeks ago By siaul... Yes, by email. They have gotten in touch with me y... 1 month ago By phi16... I contaced Prusa support but they haven't gotten b... 1 month ago By Diem view all posts
	MK2 Firmware update to 3.14.1? By martincerven 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Hi, I built MK2 back in 2016 from kit, and I print... 4 weeks ago By marti...
	Ticking sound linear rail By Niek09 4 weeks ago \| Last Post: 4 weeks ago	Hardware, firmware and software help
	Another thread is discussing this. The ticking eve... 4 weeks ago By Tim Hello everyone, Since my last print which failed (... 4 weeks ago By Niek0...